| Age | Commit message (Collapse) | Author |
|---|
|
The white balance computation didn't consider black level. This is
wrong because then the computed ratios are off when they are computed
from the whole brightness range rather than the sensor range.
This patch adjusts white balance computation for the black level. There
is no need to change white balance application in debayering as this is
already applied after black level correction.
Exposure computation already subtracts black level, no changes are
needed there.
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Reviewed-by: Andrei Konovalov <andrey.konovalov.ynk@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The documented range of values corresponds to uint8_t, so let's use that
type.
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrei Konovalov <andrey.konovalov.ynk@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add helper functions for converting between floating point and fixed
point numbers. Also add tests for them.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The ipa::RPi::IpaBase::monoSensor() function doesn't modify the class.
Make it const.
Fixes: 2031e2f29014 ("ipa: rpi: Add accessor function for monoSensor_")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
|
|
The monoSensor_ member variable will be used by the derived IPAs in an
upcoming commit, so add an accessor function for it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add support for the following HDR modes in the Raspberry Pi IPA:
- Night mode
- Single exposure mode
- Multi-exposure (merged and unmerged)
The algorithm is updated to expect the HDR short channel to meter
explicitly for highlights. This means that it will not in general
under-expose the short channel more than is actually necessary.
When images don't have much saturation, it's good to detect this so
that some of the boost we want to apply to the dark areas can be
implemented as regular gain. This means we can then adjust the tone
curve less, leading to less flat looking images.
The impact on the HDR algorithm is then that this determines how we
build tonemaps dynamically. The highlights are more-or-less correct
now, so we have to build a power-type curve that gives us the
appropriately configured targets in the lower part of the histogram.
We allow the tuning file to supply the maximum spatial gain value,
rather than the whole curve (though it can supply this if it
wants). Some parameter defaults are tweaked to be generally better
across the range of our cameras.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Acked-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The PipelineHandlerFactoryBase class has a name that is propagated to
the PipelineHandler instance it creates.
In present implementation, this name comes from the
REGISTER_PIPELINE_HANDLER registration macro. It corresponds to the
stringified name of the PipelineHandler derived class. Therefore,
PipelineHandler factories and instances names can be quite long such as
"PipelineHandlerRkISP1".
A libcamera user may have to explicitly refer to a PipelineHandler name
for configuration purpose: one usage of the name can be to define a
pipeline handlers match list and their priorities. It is desired, for
user convenience, to use a short name to designate a pipeline handler.
Reusing the short pipeline names already defined in the meson option
files is an existing and consistent way of naming pipelines.
This change adds an explicit name parameter to the
REGISTER_PIPELINE_HANDLER registration macro. That parameter is used to
define the name of a pipeline handler factory, instead of the current
pipeline handler class name.
Each pipeline registration is updated accordingly. The short name
assigned corresponds to the pipeline directory name in the source tree.
It is consistent with pipelines names used in meson.
Changing the pipeline name has an impact on the IPA modules: each module
defines a IPAModuleInfo structure. This structure has a pipelineName
member defining the pipeline handler name it shall match with.
Therefore, each internal IPA module definition has to be changed to have
its IPAModuleInfo pipelineName name updated with the short pipeline
handler name.
In addition to this pipelineName member, the IPAModuleInfo structure
also has a name member, associated to the IPA module name. Having
renamed the pipelines to a short name, the pipeline name and the IPA
module names of the IPAModuleInfo structure are the same: for in-tree
IPA, they correspond to the respective pipeline and IPA subdirectories
in the source tree. However the IPA name could be different, for
instance with a close source IPA implementation built out-of-tree. Thus,
it makes sense to keep the IPA name in that structure, as the 2
definitions may not always be redundant.
Signed-off-by: Julien Vuillaumier <julien.vuillaumier@nxp.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
[Kieran: Adjust for clang-format style fix, reformat commitmsg]
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Commit 1dc01bc9e6c3 ("ipa: libipa: histogram: Add transform parameter to
constructor") added a new constructor for the Histogram class. The
implementation is inline in the header file, and the documentation was
added in the corresponding .cpp file, but it missed the \fn directive.
This causes Doxygen to complain:
src/ipa/libipa/histogram.h:31: warning: Member Histogram(Span< const uint32_t > data, Transform transform) (function) of class libcamera::ipa::Histogram is not documented.
src/ipa/libipa/histogram.cpp:59: warning: libcamera::ipa::Histogram::bins has @param documentation sections but no arguments
Fix it.
Fixes: 1dc01bc9e6c3 ("ipa: libipa: histogram: Add transform parameter to constructor")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
|
|
Source files in libcamera start by a comment block header, which
includes the file name and a one-line description of the file contents.
While the latter is useful to get a quick overview of the file contents
at a glance, the former is mostly a source of inconvenience. The name in
the comments can easily get out of sync with the file name when files
are renamed, and copy & paste during development have often lead to
incorrect names being used to start with.
Readers of the source code are expected to know which file they're
looking it. Drop the file name from the header comment blocks in all
remaining locations that were not caught by the automated script as they
are out of sync with the file name.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
This histogram reported by the rkisp1 hardware is 20 bits, where the
upper 16 bits are meaningful integer data and the lower 4 bits are
fractional and meant to be discarded. Remove these 4 bits when
construction the histogram.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The maximum shutter speed calculation in the cam-helper relied on
the frame duration limits being correctly set in the cam-helper's mode
structure. This was not the case on first startup, so the maximum
shutter speed reported back via the ControlInfo was incorrect.
Fix this by setting up the camera mode in the cam-helper before querying
for the max shutter value.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add a parameter to the histogram constructor that takes a transformation
function to apply to all the bins upon construction.
This is necessary notably for the rkisp1, as the values reported from
the hardware are 20 bits where the upper 16-bits are meaningful integer
values and the lower 4 bits are fractional and meant to be discarded. As
adding a right-shift parameter is probably too specialized, a generic
function is added as a parameter instead.
While at it, optimize the existing constructor to avoid push_back() into
a vector with a known final size.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Source files in libcamera start by a comment block header, which
includes the file name and a one-line description of the file contents.
While the latter is useful to get a quick overview of the file contents
at a glance, the former is mostly a source of inconvenience. The name in
the comments can easily get out of sync with the file name when files
are renamed, and copy & paste during development have often lead to
incorrect names being used to start with.
Readers of the source code are expected to know which file they're
looking it. Drop the file name from the header comment block.
The change was generated with the following script:
----------------------------------------
dirs="include/libcamera src test utils"
declare -rA patterns=(
['c']=' \* '
['cpp']=' \* '
['h']=' \* '
['py']='# '
['sh']='# '
)
for ext in ${!patterns[@]} ; do
files=$(for dir in $dirs ; do find $dir -name "*.${ext}" ; done)
pattern=${patterns[${ext}]}
for file in $files ; do
name=$(basename ${file})
sed -i "s/^\(${pattern}\)${name} - /\1/" "$file"
done
done
----------------------------------------
This misses several files that are out of sync with the comment block
header. Those will be addressed separately and manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Now that the rkisp1 Agc algorithm is a derivation of MeanLuminanceAgc
we can remove the bespoke functions from the IPA's class.
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Now that we have a AgcMeanLuminance class that centralises our AEGC
algorithm, derive the RkISP1's Agc class from it and plumb in the
necessary framework to enable it to be used. For simplicities sake
this commit switches the algorithm to use the derived class, but
does not remove the bespoke functions at this time.
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Now that the IPU3's Agc is derived from MeanLuminanceAgc we can
delete all the unecessary bespoke functions.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
In preparation for switching to a derivation of AgcMeanLuminance, add
a function to parse and store the statistics for easy retrieval in an
overriding estimateLuminance() function.
Now that we have a MeanLuminanceAgc class that centralises our AEGC
algorithm, derive the IPU3's Agc class from it and plumb in the
necessary framework to enable it to be used. For simplicity's sake
this commit switches the algorithm to use the derived class, but
does not remove the bespoke functions at this time.
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The Agc algorithms for the RkIsp1 and IPU3 IPAs do the same thing in
very large part; following the Rpi IPA's algorithm in spirit with a
few tunable values in that IPA being hardcoded in the libipa ones.
Add a new base class for AgcMeanLuminance which implements the same
algorithm and additionally parses yaml tuning files to inform an IPA
module's Agc algorithm about valid constraint and exposure modes and
their associated bounds.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add a helper for managing exposure modes and splitting exposure times
into shutter and gain values.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
For convenience's sake allow the creation of empty Histograms so
they can be embedded within other Classes and filled out with
data at some later point in time.
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Provide the Sony IMX415 camera sensor properties and registration
with libipa for the gain code helpers.
The test patterns exposed by the IMX415 do not map well to the current
set of test pattern controls supplied by libcamera. These are left
intentionally unimplemented.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Provide the Sony IMX335 camera sensor properties and registration
with libipa for the gain code helpers.
The test patterns exposed by the IMX335 do not map well to the current
set of test pattern controls supplied by libcamera. These are left
intentionally unimplemented.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Provide the IMX283 camera sensor properties and registration
with libipa for the gain code helpers.
The test patterns exposed by the IMX283 do not map well to the current
set of test pattern controls supplied by libcamera. These are left
intentionally unimplemented.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
|
|
Black may not be represented as 0 pixel value for given hardware, it may
be higher. If this is not compensated then various problems may occur
such as low contrast or suboptimal exposure.
The black pixel value can be either retrieved from a tuning file for the
given hardware, or automatically on the fly. The former is the right
and correct method, while the latter can be used when a tuning file is
not available for the given hardware. Since there is currently no
support for tuning files in software ISP, the automatic, hardware
independent way, is always used. Support for tuning files should be
added in future but it will require more work than this patch.
The patch looks at the image histogram and assumes that black starts
when pixel values start occurring on the left. A certain amount of the
darkest pixels is ignored; it doesn't matter whether they represent
various kinds of noise or are real, they are better to omit in any case
to make the image looking better. It also doesn't matter whether the
darkest pixels occur around the supposed black level or are spread
between 0 and the black level, the difference is not important.
An arbitrary threshold of 2% darkest pixels is applied; there is no
magic about that value.
The patch assumes that the black values for different colors are the
same and doesn't attempt any other non-primitive enhancements. It
cannot completely replace tuning files and simplicity, while providing
visible benefit, is its goal. Anything more sophisticated is left for
future patches.
A possible cheap enhancement, if needed, could be setting exposure +
gain to minimum values temporarily, before setting the black level. In
theory, the black level should be fixed but it may not be reached in all
images. For this reason, the patch updates black level only if the
observed value is lower than the current one; it should be never
increased.
The purpose of the patch is to compensate for hardware properties.
General image contrast enhancements are out of scope of this patch.
Stats are still gathered as an uncorrected histogram, to avoid any
confusion and to represent the raw image data. Exposure must be
determined after the black level correction -- it has no influence on
the sub-black area and must be correct after applying the black level
correction. The granularity of the histogram is increased from 16 to 64
to provide a better precision (there is no theory behind either of those
numbers).
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Define the Soft IPA main and event interfaces, add the Soft IPA
implementation.
The current src/ipa/meson.build assumes the IPA name to match the
pipeline name. For this reason "-Dipas=simple" is used for the
Soft IPA module.
Auto exposure/gain and AWB implementation by Dennis, Toon and Martti.
Auto exposure/gain targets a Mean Sample Value of 2.5 following
the MSV calculation algorithm from:
https://www.araa.asn.au/acra/acra2007/papers/paper84final.pdf
Use CameraSensorHelper to convert the analogue gain code read from the
camera sensor into real analogue gain value. In the future this makes
it possible to use faster AE/AGC algorithm. Right now the CameraSensorHelper
lets us use the full range of analogue gain values.
If there is no CameraSensorHelper for the camera sensor in use, a
warning log message is printed.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # sc8280xp Lenovo x13s
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Co-developed-by: Dennis Bonke <admin@dennisbonke.com>
Signed-off-by: Dennis Bonke <admin@dennisbonke.com>
Co-developed-by: Marttico <g.martti@gmail.com>
Signed-off-by: Marttico <g.martti@gmail.com>
Co-developed-by: Toon Langendam <t.langendam@gmail.com>
Signed-off-by: Toon Langendam <t.langendam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Fix embedded data byte-skipping for 14-bit modes (4 out of 7 bytes
carry register data), and allow 14-bit modes in IMX708 PDAF parsing.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Replace manual implementations of the utils::to_underlying() helper with
calls to the function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
Handle the RKISP1_V_IMX8MP version in the rkisp1 IPA. This enables basic
support of the i.MX8MP, excluding the processing blocks specific to the
new ISP version. Those will be supported later.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
|
|
The histogram weights are initialized to hardcoded 1's for each
histogram grid cell. The code uses the wrong variable for the grid size,
resulting in some weights having a 0 value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
|
|
Versions of the ISP differ in the processing blocks they include, as
well as in the implementation of some of those blocks. In particular,
they have different numbers of histogram bins oe AE statistics cells.
The algorithms take these differences into account by checking the ISP
version reported by the driver.
These checks are currently scattered in multiple places. Centralize them
in the IPARkISP1::init() function, and store the version-dependent
hardware parameters in the IPA context, accessible by all algorithms.
While at it, drop the IPASessionConfiguration::hw member that stores the
revision number, unused by the algorithms. It can be added back laer to
the IPAHwSettings structure if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
|
|
The RkISP1 statistics structure contains multiple arrays whose length
varies depending on the hardware revision. Accessing those arrays is
error-prone, wrap them in spans at the top level to reduce risks of
out-of-bound accesses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
|
|
The CameraSensorHelperFactory::createInstance() function overrides a
virtual function from CameraSensorHelperFactoryBase. The function
declaration doesn't mark it with the override keyword. This could cause
issues in the future if the base class' function changes, as the
compiler will not issue any warning in that case. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
All the Raspberry Pi official camera tuning files are updated for
HDR. As stated previously, there is no mechanism in the hardware for
combining images so all this does is enable multi-channel AGC to
produce short and long exposure frames. It will be up to the
application to deal with them.
The changes are identical in every tuning file.
1. The existing AGC tuning is duplicated twice so that we have 3 AGC
channels.
2. The first is left alone (the default AGC channel), the second is
tweaked to under-expose significantly (ev -3) and the final one is
tweaked to over-exposure slightly (ev +0.5)
3. Control parameters are provided to the "rpi.hdr" algorithm to
associate these AGC channels correctly with the HDR modes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Sufficient plumbing is added so that the HDR mode control can be used
to engage HDR modes on platforms that support them. On the vc4
platform, this allows multi-channel AGC to run, though there is no
image merging.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Provide the OV64A40 tuning files for the Arducam Omnivision camera
module to operate on the VC4 ISP architecture on Raspberry Pi 4 and
below.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add a CameraSensorHelper for the OV64A40 camera sensor.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Support the OV64A40 sensor with a camera helper to manage the gain
model, light sensitivity, and control delays.
Signed-off-by: Lee Jackson <lee.jackson@arducam.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Implement the StatsOutputEnable control for the VC4 IPA. When set,
this outputs the ISP statistics as a uint8_t span through the Bcm2835StatsOutput
metadata control.
To get this working, IpaBase::libcameraMetadata_ is moved from a private
to a protected member variable. This makes it accessable to the VC4
derived IPA class.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
This allows the IPA to get reasonable default colour gains before AWB
has run. This is particularly important on the PiSP platform where
these numbers are helpful in programming the Front End statistics
block in advance.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
This allows the IPA to discover the correct black level values even
before any frames have been processed. This is important on the PiSP
platform where the front end black level blocks must be programmed in
advance.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Don't assert when taking the weighted mean of a zero-width or
zero-weight interval; return its upper bound. That is certainly
correct in the zero-width case, and plausible otherwise.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Advertise hardware constraints on the pixel processing rate through the
Controller::HardwareConfig structure. When calculating the minimum line
length during a configure() operation, ensure that we don't exceed this
constraint.
If we do exceed the hardware constraints, increase the modes's minimum
line length so the pixel processing rate falls below the hardware limit.
If this is not possible, throw a loud error message in the logs.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Meson uses tags to sort installed files in categories, and makes it
possible to install a subset of the files using the '--tags' argument to
'meson install'. This is typically used by distributions to split the
runtime, development and documentation files into separate packages.
By default, meson tries to guess the correct tag for installed files,
but can't always do so properly. Mark the install targets that meson
can't guess with the correct install_tag.
As the feature has been introduced in meson 0.60, bump the minimum meson
version. The latest LTS release of all major distributions that
libcamera currently targets ship a recent enough meson version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
|
|
We make a few small improvements to the code:
* The arrayToSet method is prevented from overwriting the end of the
array if there are too many values in the input table. If you supply
a table, it will force you to put the correct number of elements in
it.
* The arrayToSet and setStrength member functions are turned into
static functions. (There may be a different public setStrength
member function in future.)
* When no tables at all are given, the configuration is flagged as
being disabled, so that we can avoid copying tables full of zeroes
around. As a consequence, the pipeline handler too will disable this
hardware block rather than run it needlessly. (Note that the tuning
tool will put in a completely empty "rpi.cac" block if no CAC tuning
images are supplied, benefiting from this behaviour.)
* The initialise member function is removed as it does nothing.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The recent change where time-filtering is done before sorting out the
digital gain means that the target exposure without digital gain is no
longer set, breaking the 'AeLocked' calculation.
We can use the regular (full) target exposure instead.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Fixes: 84b6327789fc ("ipa: rpi: agc: Filter exposures before dealing with digital gain")
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Label draft controls and properties through the "draft" vendor tag
and deprecate the existing "draft: true" mechanism. This uses the new
vendor tags mechanism to place draft controls in the same
libcamera::controls::draft namespace and provide a defined control id
range for these controls. This requires moving all draft controls from
control_ids.yaml to control_ids_draft.yaml.
One breaking change in this commit is that draft control ids also move
to the libcamera::controls::draft namespace from the existing
libcamera::controls namespace. This is desirable to avoid API breakages
when adding new libcamera controls. So, for example, the use of
controls::NOISE_REDUCTION_MODE will need to be replaced with
controls::draft::NOISE_REDUCTION_MODE.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The algorithm computes R/G and B/G colour ratio statistics which we
should not allow to go to zero because there is clearly no gain you
could apply to R or B to equalise them. Instead flag such regions as
having "insufficient data" in the normal manner.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
We need to be able to do things like enable/disable AGC for all the
channels, so most of the AGC controls are updated to be applied to all
channels. There are a couple of exceptions, such as setting explicit
shutter/gain values, which apply only to channel 0.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
AWB writes this out during prepare, so we may as well read it in AGC
prepare as well. Reading it in process is wrong on the PiSP platform
because process runs before prepare, so the AWB status won't be there
(on vc4 it made no difference).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Since noise control handling differs between the VC4 and PiSP IPAs,
move the current denoise control handler from ipa base into the vc4 IPA
derived class.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
