| Age | Commit message (Collapse) | Author |
|---|
|
Since VCM for surface Go 2 (dw9719) had been successfully driven, this
Af module can be used to control the VCM and determine the focus value
based on the IPU3 AF state.
Based on the values from the IPU3 AF buffer, the variance of each focus
step is determined and a greedy approach is used to find the maximum
variance of the AF state and an appropriate focus value.
The grid configuration is implemented as a context. Also, the grid
parameter- AF_MIN_BLOCK_WIDTH is set to 4 (default is 3) since if the
default value is used, x_start (x_start > 640) will be at an incorrect
location of the image (rightmost of the sensor).
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The algorithms are using the same function names with specialized
parameters. Instead of duplicating code, introduce a libipa Algorithm
class which implements a base class with template parameters in libipa,
and use it in each IPA.
As we now won't need an algorithm class for each IPA, move the
documentation to libipa, and make it agnostic of the IPA used. While at
it, fix the IPU3::Algorithm::Awb documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
|
|
The pixels output by the camera normally include a black level, because
sensors do not always report a signal level of '0' for black. Pixels at
or below this level should be considered black and to achieve that, we
need to substract an offset to all the pixels. This can be taken into
account by reading the lowest value of a special region on sensors which
is not exposed to light. This provides a substracting factor to be
able to adjust the expected black levels in the resulting images.
For a camera outputting 10-bit pixel values (in the range 0 to 1023) a
typical black level might be 64. It is a fixed value, obtained by
capturing a raw frame with minimum exposure and gain fixed to 1.0 while
covering the sensor (the darker the better). We consider it good enough
as a very first approximation, until we measure it during a tuning
process and include it in a configuration file
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Now that the interface is properly used by the AGC class, move it into
ipa::ipu3::algorithms and let the loops do the calls.
As we need to exchange the exposure_ and gain_ by passing them through the
FrameContext, use the calculated values in setControls() function to
ease the reading.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Now that the interface is properly used by the AWB class, move it into
ipa::ipu3::algorithms and let the loops do the calls.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Introduce a new algorithm to manage the tone mapping handling of the
IPU3.
The initial algorithm is chosen to configure the gamma contrast curve
which moves the implementation out of AWB for simplicity. As it is
initialised with a default gamma value of 1.1, there is no need to use
the default table at initialisation anymore.
This demonstrates the way to use process() call when the EventStatReady
comes in. The function calculates the LUT in the context of a frame, and
when prepare() is called, the parameters are filled with the updated
values.
AGC is modified to take the new process interface into account.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The abstract Algorithm class was originally placed in libipa as an
attempt define a generic algorithm container. This was a little
optimistic and pushed a bit far too early.
Move the Algorithm class into the IPU3 which is the only user of the
class, as we adapt it to support modular algorithm components for the
IPU3.
Not documenting the namespace may cause issues with Doxygen in libipa.
The file libipa.cpp is thus created as an empty file for now, but we
can leverage it in the future to add more global libipa documentation,
and possibly code too.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
