| Age | Commit message (Collapse) | Author |
|---|
|
In cases where the calibration image contains super dark areas, or when
an invalid blacklevel was supplied, the grid might get close to zero or
negative. This would have bad effects on the 1/grid later. So clamp the
values to a small positive number.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
The current LSC algorithm for the rkisp1 just forwards the LSC tables to
the hardware, so absolute factors are needed and not ratios compared to
green. Therefore every channel needs to be calculated independently.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Add awb, blc, cproc, filter, and gamma to the tuning file. These don't
need any configuration.
At the moment there are no inter-module dependencies in the tuning
process. We can therefore safely sort them alphabetically. As soon as
the first dependency gets introduced (most likely lsc -> ccm) we will
see how to solve that.
The output order controls the order of processing in the IPA. It is now
also in alphabetical order which happens to be no change for the modules
that existed previously. For the others, there is no need for a specific
order.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Add a static module class, that can be used to add static data to the
tuning file. This is propably not the best solution, but allows us to
progress without writing lots of dummy classes for static cases.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
There are valid cases where a module returns None. E.g. no images were
provided for LSC calibration. We should however define proper semantics
there. Continue with a warning for now.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Make it clear that no lsc calibration was done by returning None instead
of a incomplete configuration.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Implement a minimal ccm calibration module. For now it doesn't take the
results from lsc into account and supports rkisp1 only.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Remove the need for the Cam object, as we don't want to port
it from Raspberry Pi.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
In the Image class the variable holding the color temperature is named
color instead of col which was used by the raspberry pi scripts. Rename
accordingly.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Based on the input images, the lsc values could exceed the range allowed
by the rkisp1. As we are now clipping the values, we can simplify the
value mapping.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Print a info on every image that gets processed and a warning on every
image that gets ignored.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Add the missing pieces and store the result inside the image object.
This solution is not very nice, and should be refactored soon. For that
we need a concept to collect temperature and/or image specific results
in a central place. For now it serves the purpose.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
At the moment this just reads the yaml file and returns it verbatim.
This needs to evolve further in the near future.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In the tuning datasets, the files had names like
'imx335_1600l_3000k_1.dng'. That failed on the old filename parsing
function. As there is no need to dictate the order of the tags, split
the big regex into chunks and parse them one by one. This also makes
the code easier to digest.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The old function uses PIL to save the image, which is not in the
requirements file. As we are already requiring opencv, use that to save
images instead of an additional dependency
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In ctt_ccm.py the logging functionality of the Cam object was used. As
we don't want to port over that class, it needs to be replaced anyways.
While at it, also replace the eprint function as it doesn't add any
value over the logging framework and misses the ability for easy log
formatting.
For nice output formatting add the coloredlogs library.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Fix imports to match new structure in the files copied from Raspberry
Pi. Add missing imports in macbeth.py. Add missing dependencies to
requirements.txt.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Add a requirements file to ease the installation and use of the tuning
scripts. Document that in the readme. No debian packages are provided as
rawpy is not packaged as deb. So pip has to be used anyways.
Also add pyyaml which was missing in the dependencies.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Copy visualize_macbeth_chart from raspberry pi. It is copied verbatim
and does not work in this state.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Copy ctt_{awb,ccm,colors,ransac} from the raspberrypi tuning scripts as
basis for the libcamera implementation. color.py was renamed to
ctt_colors.py to better express the origin.
The files were taken from commit 66479605baca ("utils: raspberrypi: ctt:
Improve the Macbeth Chart search reliability").
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Acked-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Opencv fails to load the image. The added license destroys the magic
number. Fix, by moving the licence below the magic number.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul ELder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Port commit 66479605baca ("utils: raspberrypi: ctt: Improve the Macbeth
Chart search reliability") into libtuning.
Previously the code would brighten up images in case the Macbeth Chart
is slightly dark, and also zoom in on sections of it to look for
charts occupying less of the field of view. But it would not do both
together.
This change makes the search for smaller charts also repeat that
search for the brightened up images that it made earlier, thereby
increasing the chances of success for non-optimal tuning images.
Signed-off-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The Image class incorrectly parses data in GBRG bayer formats as the
indices to the channels are set incorrectly - fix it.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add the skeletal AGC module to the rkisp1 tuning script. For now it just
spits out hardcoded values.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Add a skeletal AGC module just so that we can have some AGC tuning
values that we can use to test during development of AGC in the IPAs. As
rkisp1 is the main target, we only add support for rkisp1 for now.
The parameters are mostly copied from the hardcoded values in ctt,
except for the metering modes.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Source files in libcamera start by a comment block header, which
includes the file name and a one-line description of the file contents.
While the latter is useful to get a quick overview of the file contents
at a glance, the former is mostly a source of inconvenience. The name in
the comments can easily get out of sync with the file name when files
are renamed, and copy & paste during development have often lead to
incorrect names being used to start with.
Readers of the source code are expected to know which file they're
looking it. Drop the file name from the header comment block.
The change was generated with the following script:
----------------------------------------
dirs="include/libcamera src test utils"
declare -rA patterns=(
['c']=' \* '
['cpp']=' \* '
['h']=' \* '
['py']='# '
['sh']='# '
)
for ext in ${!patterns[@]} ; do
files=$(for dir in $dirs ; do find $dir -name "*.${ext}" ; done)
pattern=${patterns[${ext}]}
for file in $files ; do
name=$(basename ${file})
sed -i "s/^\(${pattern}\)${name} - /\1/" "$file"
done
done
----------------------------------------
This misses several files that are out of sync with the comment block
header. Those will be addressed separately and manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Change the names of python packages in the list of dependencies to the
exact names that should be used in the pip install command.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
|
|
Add a tuning script for rkisp1 that uses libtuning. So far it only
supports LSC.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a tuning script for raspberrypi for alsc only, that uses libtuning.
Since there will also be a tuning script for raspberrypi that has more
modules, put the libtuning alsc module definition in a separate file so
that it can be reused later.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a generator to libtuning for writing tuning output to a yaml file.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a parser to libtuning for parsing configuration files in yaml
format.
At the moment it doesn't parse anything and simply returns an empty
config. This is fine for the time being, as the only user of it is the
rkisp1 tuning script, which only has an LSC module which doesn't consume
anything from the configuration file. When a module comes around that
requires the yaml parser, it can be implemented then.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a generator to libtuning for writing tuning output to a json file
formatted the same way that raspberrypi's ctt formats them.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a parser to libtuning for parsing configuration files that are the
same format as raspberrypi's ctt's configuration files.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add an LSC module for RkISP1.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add an ALSC module for Raspberry Pi.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a base LSC module to libtuning's collection of modules. It is based
on raspberrypi's ctt's ALSC, but customizable for different lens shading
table sizes, among other things. It alone is insufficient as a module,
but it provides utilities that are useful for and which will simplify
implementing LSC modules.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Implement the extensible components of libtuning. This includes:
- Parsers, for supporting different types of input config file formats
- Generators, for supporting different types of output tuning file
formats
- Modules, for supporting different tuning modules for different
algorithms and platforms
No parsers, generators, or modules are actually implemented. Only the
base classes are implemented.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Implement math helpers for libtuning. This includes:
- Average, a wrapper class for numpy averaging functions
- Gradient, a class that represents gradients, for distributing and
mapping
- Smoothing, a wrapper class for cv2 smoothing functions
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Implement the core of libtuning, our new tuning tool infrastructure. It
leverages components from raspberrypi's ctt that could be reused for
tuning tools for other platforms.
The core components include:
- The Image class
- libtuning (entry point and other core functions)
- macbeth-related tools, including the macbeth reference image
- utils
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
