| Age | Commit message (Collapse) | Author |
|---|
|
Rename CamHelper::getVBlanking to CamHelper::getBlanking, and update the
calculations in that function to return both horizontal and vertical
blanking values for a given exposure time and frame duration limits. The
calculations are setup such that vertical blanking is extended to the
maximum allowable value, and any remainder gets put into horizontal
blanking.
The calculated horizontal blanking value is now returned to the pipeline
handler to pass into DelayedControls to program into the sensor.
Update the IPA to now specify the maximum frame duration from the
maximum horizontal + vertical blanking values provided by the sensor
mode. Additionally, the IPA now uses the frame specific horizontal
blanking value (as returned by DelayedControls) in all instances.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a lineLength field to the DeviceStatus structure to store the line
length used for a particular frame.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The pixel clock rate will be used in subsequent commits to calculate
line length durations.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Update CamHelper::getDelays() to return the sensor HBLANK delay. The
HBLANK delay is set to the same value as VBLANK delay for all sensors in
the Raspberry Pi IPA.
Return the HBLANK gain delay from the IPA to the pipeline handler, and
initialise DelayedControls to handle V4L2_CID_HBLANK with this delay
value.
As a drive-by, check that the V4L2_CID_HBLANK control is available when
calling IPARPi::configure().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Update CamHelper::exposureLines() and CamHelper::exposure() to take a
line length duration parameter for use in the exposure calculations.
For now, only use the minimum line length for all the calculations to
match the existing IPA behavior.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add fields for minimum and maximum line length duration to the
CameraMode structure. This replaces the existing lineLength field.
Any use of the existing lineLength field is replaced by the new
minLineLength field, as logically we always want to use the fastest
sensor readout by default.
As a drive-by cosmetic change, split all fields in the CameraMode
structure into separate lines.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add fields for minimum and maximum line length (in units of pixels) to
the IPACameraSensorInfo structure. This replaces the existing lineLength
field.
Update the ipu3, raspberrypi and rkisp1 IPAs to use
IPACameraSensorInfo::minLineLength instead of
IPACameraSensorInfo::lineLength, as logically we will always want to use
the fastest sensor readout by default.
Since the IPAs now use minLineLength for their calculations, set the
starting value of the V4L2_CID_HBLANK control to its minimum in
CameraSensor::init().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Commit 09c1b081baa2 ("libcamera: controls: Generate and use fixed-sized
Span types") added explicit Span casts for fixed extent spans that were
required due to the ControlList::set() function that takes an
std::initializer_list not being able to infer a control size from
template arguments. This has now been fixed, so the casts are not needed
anymore. Drop them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Christian Rauch <Rauch.Christian@gmx.de>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
|
|
These headers are not used as reported by clangd.
Signed-off-by: Christian Rauch <Rauch.Christian@gmx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Define Span types explicitly as either variable- or fixed-sized. This
introduces a new convention for defining Span dimensions in the property
and control value definitions and generates Span types as variable-sized
Span<T> or as fixed-sized Span<T,N>.
Signed-off-by: Christian Rauch <Rauch.Christian@gmx.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The Raspberry Pi IPA module depends on boost only to parse the JSON
tuning data files. As libcamera depends on libyaml, use the YamlParser
class to parse those files and drop the dependency on boost.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
When encountering errors, the Algorithm::read() function either uses
LOG(Fatal) or throws exceptions from the boost property_tree functions.
To prepare for replacing boost JSON parse with the YamlParser class,
give the Algorithm::read() function the ability to return an error code,
and propagate it all the way to the IPA module init() function.
All algorithm classes return a hardcoded 0 value for now, subsequent
commits will change that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: Naushir Patuck <naush@raspberrypi.com>
|
|
Replace all #define constant values with equivalent constexpr definitions.
As a drive-by, remove the CAMERA_MODE_NAME_LEN constant as it is unused.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
s/Raspberry Pi (Trading) Limited/Raspberry Pi Ltd/ to reflect the new
Raspberry Pi entity name.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
As per the libcamera coding guidelines, rename all .hpp header files to .h.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Refactor all the source files in src/ipa/raspberrypi/ to match the recommended
formatting guidelines for the libcamera project. The vast majority of changes
in this commit comprise of switching from snake_case to CamelCase, and starting
class member functions with a lower case character.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Previously, ControlList::get<T>() would use default constructed objects to
indicate that a ControlList does not have the requested Control. This has
several disadvantages: 1) It requires types to be default constructible,
2) it does not differentiate between a default constructed object and an
object that happens to have the same state as a default constructed object.
std::optional<T> additionally stores the information if the object is valid
or not, and therefore is more expressive than a default constructed object.
Signed-off-by: Christian Rauch <Rauch.Christian@gmx.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The ipa currently advertises a static ControlInfoMap to specify the available
controls and their limits. Fix this limitation by having the IPA populate a new
ControlInfoMap with updated limits for ExposureTime, AnalogueGain, and
FrameDurationLimits controls based on the current sensor mode. This new
ControlInfoMap is then returned back to the pipeline handler and available to
the application after a successful Camera::configure() call.
Before the first call to Camera::configure(), this ControlInfoMap provides some
reasonable default limits for ExposureTime, AnalogueGain, and
FrameDurationLimits. However, applications must not rely on these values, but
obtain the correct limits after the call to Camera::configure().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Currently the pipeline handler advertises controls handled by the IPA from a
static ControlInfoMap defined in the raspberrypi.h header. This change removes
this header file, and instead the IPA returns the ControlInfoMap to the pipeline
handler from the ipa::init() function. This is done to allow the IPA to adjust
the limits of the controls based on the sensor mode in a subsequent change.
Bug: https://bugs.libcamera.org/show_bug.cgi?id=83
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add an optional sensor_temperature field to the DeviceStatus structure. If a
temperature measurement is available for a frame, the value is returned out
through the SensorTemperature control in the Request metadata.
Additionally, provide the sensor temperature value from the std::ostream &operator<<
overload.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
These changes retrieve the correct value for sensitivity of the mode
selected for the sensor. This value is known to the CamHelper which
passes it across to the pipeline handler so that it can be set
correctly in the camera properties.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The message that prints all controls in a request in
IPARPi::queueRequest() is noisy. Demote it from Info to Debug.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
Simplify name-spacing of the RPi components by placing it in the
ipa::RPi namespace directly. It also aligns the RPi IPA with the other
ones (ipa::ipu3 and ipa::rkisp1) which already have this applied.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Enable the V4L2VideoDevice dequeue timeout for the Unicam Image node, and
connect the timeout signal to a slot in the pipeline handler. This slot will
log an error message informing the user of a possible hardware stall.
The timeout is calculated as 2x the maximum frame length possible for a given
mode, returned by the IPA.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The AwbAuto mode is defined in all the JSON tuning files as "auto",
not "normal". The effect of this was that you couldn't switch back to
"auto" mode once you had switched away.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
With the controller algorithms running at 60fps, there are some dropped frames
when running at very high famerates. Reducing this to 30fps eliminates all these
drops without any noticeable changes to the image quality.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Limit the gain code to the maximum value reported by the sensor controls
when sending to DelayedControls. The AGC algorithm will handle a lower
gain used by the sensor, provided it knows the actual gain used. This
change ensures that DelayedControls will never report an unclipped gain
used.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
For consistency with UniqueFD, rename the fd() function to get().
Renaming UniqueFD::get() to fd() would have been another option, but was
rejected to keep as close as possible to the std::shared_ptr<> and
std::unique_ptr<> APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
|
|
Now that we have a UniqueFD class, the name FileDescriptor is ambiguous.
Rename it to SharedFD.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The FileDescriptor class is a generic helper that matches the criteria
for the base library. Move it there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When the pipeline handler start() method is supplied with a NULL list
of controls, we send an empty control list to the IPA. When the IPA is
running in isolated mode the control list goes through the data
serializer, for which it must be marked correctly as a list of
"controls::controls", otherwise the IPA process will abort.
The IPA has a similar problem returning a control list in its
configure() method. We must be careful to initialise it properly even
when empty.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
MappedFrameBuffer::maps() returns planes_. This renames the function
name to planes().
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Remove the need for callers to reference PROT_READ/PROT_WRITE directly
from <sys/mman.h> by instead exposing the Read/Write mapping options as
flags from the MappedFrameBuffer class itself.
While here, introduce the <stdint.h> header which is required for the
uint8_t as part of the Plane.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The MappedFrameBuffer is a convenience feature which sits on top of the
FrameBuffer and facilitates mapping it to CPU accessible memory with
mmap.
This implementation is internal and currently sits in the same internal
files as the internal FrameBuffer, thus exposing those internals to
users of the MappedFramebuffer implementation.
Move the MappedFrameBuffer and MappedBuffer implementation to its own
implementation files, and fix the sources throughout to use that
accordingly.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Usage of 'method' to refer to member functions comes from Java. The C++
standard uses the term 'function' only. Replace 'method' with 'function'
or 'member function' through the whole code base and documentation.
While at it, fix two typos (s/backeng/backend/).
The BoundMethod and Object::invokeMethod() are left as-is here, and will
be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
We use the CamHelper class to initialise it to the usual value of 1.
The CamHelper's GetModeSensitivity method can be redefined to
implement a different behaviour for sensors that require it.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Return controls::FrameDuration through the per-frame Request metadata.
The frame duration is obtained by either the value in DelayedControls,
or (preferably) the value parsed from the embedded data buffer.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
s/DefaultAnalogueGain/defaultAnalogueGain/
s/DefaultExposureTime/defaultExposureTime/
Change these for consistency with the other static const variables.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
With the recent change to allow long exposures on the imx477, the existing 100s
limit was not adequate.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Store the frame length into the DeviceStatus struct. The value is extracted
from embedded data when available, or calculated from the VBLANK value passed
from DelayedControls otherwise.
Update imx477 and imx219 CamHelper classes to extract the frame length from the
embedded data buffer.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add an operator<< overload to log all fields in DeviceStatus, and remove the
manual logging statements in the IPA and CamHelper.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
libcamera names header files based on the classes they define. The
buffer.h file is an exception. Rename it to framebuffer.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Move span, and adjust the Doxygen exclusion as well.
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Move the functionality for the following components to the new
base support library:
- BoundMethod
- EventDispatcher
- EventDispatcherPoll
- Log
- Message
- Object
- Signal
- Semaphore
- Thread
- Timer
While it would be preferable to see these split to move one component
per commit, these components are all interdependent upon each other,
which leaves us with one big change performing the move for all of them.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Convert the core AGC and Lux controller code to use
utils::Duration for all exposure time related variables and
calculations.
Convert the exposure/shutter time fields in AgcStatus and DeviceStatus
to use utils::Duration.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Switch the AgcAlgorithm API functions to use utils::Duration for all
time based variables.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Switch the ipa and cam_helper code to use libcamera::utils::Duration for
all time based variables. This improves code readability and avoids
possible errors when converting between time bases.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
We need a separate control to report the nominal frame duration, but
it's also useful to report the min/max frame duration values that will
be used. Split the FrameDurations control into FrameDuration and
FrameDurationLimits respectively to support both of these.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
This matches the naming convention for IPA IPC.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Acked-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
CameraSensorInfo structure is designed to pass in camera sensor related
information from pipeline-handler to IPA. Since the pipeline-handler
and IPA are connected via mojom IPC IPA interface, the interface
itself provides a more suitable placement of CameraSensorInfo,
instead of camera_sensor.h (which is a libcamera internal header
ultimately, at this point).
As CameraSensorInfo is already defined in core.mojom, it is just
a matter of removing [skipHeader] tag to allow code-generation
of CameraSensorInfo.
Finally, update header paths to include CameraSensorInfo definition
from IPA interfaces instead of "libcamera/internal/camera_sensor.h".
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
