| Age | Commit message (Collapse) | Author |
|---|
|
Since meson v0.49.0, join_paths() is equivalent to '/' hence,
drop and replace it with '/' short-hand in meson files.
This commit does not introduce any functional changes.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
This patch adds support for the Soho Enterprises SE327M12 module. The
sensor is an imx327 which therefore uses the imx290 kernel driver and
CamHelper.
To use this module and camera tuning, place the following in the
/boot/config.txt file:
dtoverlay=imx290,clock-frequency=37125000
and then the existing imx290.json file must be over-written with
se327m12.json
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
imx290 and imx327 share the same kernel driver (imx290.c) and are
therefore both recognised here as "imx290". We add the necessary
CamHelper for these sensors, as well as a camera tuning file.
The tuning was done with an Innomaker STARVIS IMX327LQR module. These
have no IR cut filter so there is no proper colour tuning. However,
you should obtain reasonable results for most modules using this
sensor. Specific tunings for further modules can always be added
subsequently.
To use this sensor on the Raspberry Pi platform, please add
dtoverlay=imx290,clock-frequency=74250000
into your /boot/config.txt file.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Set the maximum shutter speed for the normal exposure profile to 66ms,
allowing viewfinder framerates to go down to approx. 15fps.
Set the maximum shutter speed for the sport exposure profile to 33ms,
limiting the minimum framerate to approx. 30fps.
Add a long exposure profile to allow shutter speeds of up to 120ms.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The exposure times in the exposure modes were causing AGC oscillations
because the algorithm was demanding long unachievable exposure times
but, without working sensor metadata, thought it was getting them when
actually it was not. We fix it by making the exposure profile request
only achievable exposure times, as we do for the ov5647 tuning.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The names have to match for the setting to work. Use the libcamera
terminology for consistency (even though it touches more files).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Previously, output of the focus measure could not be enabled without
recompiling (because of the RPI_LOGGING_ENABLE macro). This uses the
libcamera logging mechanism instead, so can be enabled/disabled at
runtime.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Adds FocusStatus to the image metadata, containing contrast measurements
across the image. Optionally also prints a contrast measure to the
console, to aid in manual adjustment of the lens. Note that it is not an
actual auto-focus algorithm that can drive a lens!
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add missing SPDX headers to miscellaneous small files. Use CC0-1.0 for
meson.build, .gitignore and the small include/linux/README, and licenses
matching the corresponding component for other files.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Initial implementation of the Raspberry Pi (BCM2835) libcamera IPA and
associated libraries.
All code is licensed under the BSD-2-Clause terms.
Copyright (c) 2019-2020 Raspberry Pi Trading Ltd.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
