| Age | Commit message (Collapse) | Author |
|---|
|
When a new CameraConfiguration is applied to the Camera the IPA is
configured as well, using the newly applied sensor configuration and its
updated V4L2 controls.
Also update the Camera controls at IPA::configure() time by re-computing
the controls::ExposureTime and controls::FrameDurationLimits limits and
update the controls on the pipeline handler side after having configured
the IPA.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The pixels output by the camera normally include a black level, because
sensors do not always report a signal level of '0' for black. Pixels at
or below this level should be considered black and to achieve that, we
need to substract an offset to all the pixels. This can be taken into
account by reading the lowest value of a special region on sensors which
is not exposed to light. This provides a substracting factor to be
able to adjust the expected black levels in the resulting images.
For a camera outputting 10-bit pixel values (in the range 0 to 1023) a
typical black level might be 64. It is a fixed value, obtained by
capturing a raw frame with minimum exposure and gain fixed to 1.0 while
covering the sensor (the darker the better). We consider it good enough
as a very first approximation, until we measure it during a tuning
process and include it in a configuration file
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The statistics buffer 'ipu3_uapi_awb_raw_buffer' stores the ImgU
calculation results in a buffer aligned horizontally to a multiple of 4
cells. The AWB loop should take care of it to add the proper offset
between lines and avoid any staircase effect.
It is no longer required to pass the grid configuration context to the
private functions called from process() which simplifies the code flow.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The loops over the width and height of the image when calculating the
BDS grid parameters are nested, but they're actually independent. Split
them to reduce the complexity.
While at it, split out the constants to documented const expressions
for the grid sizes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Until now, the limits used to calculate the grid based on the Bayer Down
Scaler configuration where taken from the kernel documentation [0].
While testing and understanding the format of the ImgU statistics, it
appears that the ones defined in CrOS [1] are the correct ones. Use
those.
[0] https://www.kernel.org/doc/html/latest/userspace-api/media/v4l/pixfmt-meta-intel-ipu3.html?highlight=v4l2_meta_fmt_ipu3_params#intel-ipu3-imgu-uapi-data-types
[1] https://chromium.googlesource.com/chromiumos/platform/arc-camera/+/refs/heads/master/hal/intel/include/ia_imaging/awb_public.h
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The IPA::configure() function has an IPAConfigInfo parameters which
contains a map of numerical indexes to ControlInfoMap instances.
This is a leftover of the old IPA protocol, where it was not possible to
specify a rich interface as it is possible today and each entity
ControlInfoMap was indexed by a numerical id and stored in a map.
Now that the IPA interface allows to specify parameters by name, drop the
map and send the sensor's control info map only.
If we'll need more ControlInfoMap to be shared with the IPA, a new parameter
can be added to IPAConfigInfo.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The incoming params buffer may contain uninitialised data, or the
parameters of previously queued frames. Clearing the entire buffer
may be an expensive operation, and the kernel will only read from
structures which have their associated use-flag set.
It is the responsibility of the algorithms to set the use flags
accordingly for any data structure they update during prepare().
Clear the use flags of the parameter buffer before passing the buffer
to the algorithms during their prepare() operations.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
MappedFrameBuffer::maps() returns planes_. This renames the function
name to planes().
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Now that the interface is properly used by the AGC class, move it into
ipa::ipu3::algorithms and let the loops do the calls.
As we need to exchange the exposure_ and gain_ by passing them through the
FrameContext, use the calculated values in setControls() function to
ease the reading.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Now that the interface is properly used by the AWB class, move it into
ipa::ipu3::algorithms and let the loops do the calls.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In preparation for using the AGC through the new algorithm interfaces,
convert the existing code to use the new function types.
Now that the process call is rewritten, re-enable the compiler flag to
warn when a function declaration hides virtual functions from a base class
(-Woverloaded-virtual).
We never use converged_ so remove its declaration. The controls may not
need to be updated at each call, but it should be decided on the context
side and not by a specific call by using a lock status in the Agc
structure for instance.
As the params_ local variable is not useful anymore, remove it here
too.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
When the stats are received, pass them with the context to the existing
AWB algorithm. IPAFrameContext now has a new structure to store the
gains calculated by the AWB algorithm.
When an EventFillParams event is received, call prepare() and set the new
gains accordingly in the params structure.
There is no more a need for the IPU3Awb::initialise() function, as the
params are always set in prepare().
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Introduce a new algorithm to manage the tone mapping handling of the
IPU3.
The initial algorithm is chosen to configure the gamma contrast curve
which moves the implementation out of AWB for simplicity. As it is
initialised with a default gamma value of 1.1, there is no need to use
the default table at initialisation anymore.
This demonstrates the way to use process() call when the EventStatReady
comes in. The function calculates the LUT in the context of a frame, and
when prepare() is called, the parameters are filled with the updated
values.
AGC is modified to take the new process interface into account.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Implement a new modular framework for algorithms with a common context
structure that is passed to each algorithm through a common API.
This patch:
- removes all the local references from IPAIPU3 and uses IPAContext
- implements the list of pointers and the loop at configure call on each
algorithm
- loops in fillParams on each prepare() call on the algorithm list
- loops in prepareStats on each process() call on the algorithm list
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
An increasing amount of data and information needs to be shared between
the components that build up to implement image processing algorithms.
Create a context structure which will allow us to work towards calling
algorithms in a modular way, and sharing information between the modules.
The IPA context is a global context set at configure time
(IPASessionConfiguration) and a per-frame context (IPAFrameContext) used
while streaming.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Tidy-up a bit the inclusions directive in the IPU3 IPA module.
In detail:
- ipu3.cpp is missing inclusions for:
std::abs from <cmath>
std::map from <map>
std::min/max from <algorithm>
std::numeric_limits from <limits>
std::unique_ptr from <memory>
std::vector from <vector>
and does not require <sys/mman.h>
- ipu3_agc has two not used inclusions in the header file and one the cpp file
and is missing <chrono> for std::literals::chrono_literals
- ipu3_awb is missing <algorithm> for std::sort and does not use
<numeric> or <unordered_map>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
All the IPU3 Camera controls are currently initialized by the pipeline
handler which initializes them using the camera sensor configuration and
platform specific requirements.
However, some controls are better initialized by the IPA, which might,
in example, cap the exposure times and frame duration to the constraints
of its algorithms implementation.
Also, moving forward, the IPA should register controls to report its
capabilities, in example the ability to enable/disable 3A algorithms on
request.
Move the existing controls initialization to the IPA, by providing
the sensor configuration and its controls to the IPU3IPA::init()
function, which initializes controls and returns them to the pipeline
through an output parameter.
The existing controls initialization has been copied verbatim from the
pipeline handler to the IPA, if not a for few line breaks adjustments
and the resulting Camera controls values are not changed.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
|
|
Remove the need for callers to reference PROT_READ/PROT_WRITE directly
from <sys/mman.h> by instead exposing the Read/Write mapping options as
flags from the MappedFrameBuffer class itself.
While here, introduce the <stdint.h> header which is required for the
uint8_t as part of the Plane.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The MappedFrameBuffer is a convenience feature which sits on top of the
FrameBuffer and facilitates mapping it to CPU accessible memory with
mmap.
This implementation is internal and currently sits in the same internal
files as the internal FrameBuffer, thus exposing those internals to
users of the MappedFramebuffer implementation.
Move the MappedFrameBuffer and MappedBuffer implementation to its own
implementation files, and fix the sources throughout to use that
accordingly.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Usage of 'method' to refer to member functions comes from Java. The C++
standard uses the term 'function' only. Replace 'method' with 'function'
or 'member function' through the whole code base and documentation.
While at it, fix two typos (s/backeng/backend/).
The BoundMethod and Object::invokeMethod() are left as-is here, and will
be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
libcamera names header files based on the classes they define. The
buffer.h file is an exception. Rename it to framebuffer.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
In order for the CameraSensorHelper to be instantiated, we need to find
its factory using the camera sensor model name stored in
IPASettings::sensorModel. As we don't need to do it at each configure
call (the sensor is not changing in-between), implement the init call in
IPAIPU3 to do that.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Move the functionality for the following components to the new
base support library:
- BoundMethod
- EventDispatcher
- EventDispatcherPoll
- Log
- Message
- Object
- Signal
- Semaphore
- Thread
- Timer
While it would be preferable to see these split to move one component
per commit, these components are all interdependent upon each other,
which leaves us with one big change performing the move for all of them.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The IPU3 IPA interface does not define a return value from configure().
This prevents errors from being reported back to the pipeline handler
when they occur in the IPA.
Update the IPU3 IPA interface and add return values to the checks in
IPAIPU3::configure() accordingly
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Frame duration is hard-coded for CTS as per [1]. Ideally, to accurately
calculate the frame duration, it needs the VBLANK value from every
frame's exposure. However, this particular bit is yet to be implemented
in IPAIPU3.
Meanwhile, we can at least head in the right direction by not hard
coding the value, instead using the default VBLANK value as reported
by the sensor. Update the existing \todo, to use the derived VBLANK
value as and when it's available from each frame exposure.
[1] 6c5f3fe6ced7 ("ipa: ipu3: Set output frame duration metadata")
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
IPACameraSensorInfo members will be needed at various places in the
IPAIPU3 class, in subsequent commits. Hence, it seems trivial to copy
this structure for wider availability throughout the class.
This commit does not introduce any functional changes.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
Squash \todo by calculating line duration from IPACameraSensorInfo,
now passed in, to IPU3Agc::initialise().
Since line duration is now calculated from real values, store it as a
private member in IPU3Agc class. As a further step, replace the
associated global constant, kMaxExposureTime, with a private IPU3Agc
class member as well, and assign its value correspondingly in
IPU3Agc::initialise(), similar to previous precedence.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
The sensor frame duration should be set by the IPA. Hardcode it for now.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
|
|
Pass in frame timestamps from IPU3 pipeline handler to IPU3 IPA via
IPU3Event. Frame timestamps are helpful to IPA algorithms to
convergence, by setting them via IPA stats.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
IPAConfigInfo is a consolidated data structure passed from IPU3
pipeline-handler to IPU3 IPA. The structure can be extended with
additional parameters to accommodate the requirements of multiple
IPU3 IPA modules.
Adapt the in-tree IPU3 IPA to use IPAConfigInfo as well.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Implement basic auto-exposure (AE) and auto-gain (AG) correction functions.
The functions computeTargetExposure() and computeGain() are adapted from
the Raspberry Pi AGC implementation to suit the IPU3 structures, and
filtering is added to reduce visible stepsize when there are large
exposure changes.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The IPA will locally modify the parameters before they are passed down
to the ImgU. Use a local parameter object to give a reference to those
algorithms.
Inherit from the Algorithm class to implement basic AWB functions.
The configure() call will set exposure and gain to their minimum value,
so while AGC is not there, the frames will be dark.
Once AWB is done, a color temperature is estimated and a default CCM matrix
will be used (yet to be tuned).
Implement a basic "grey-world" AWB algorithm just for demonstration purpose.
The BDS output size is passed by the pipeline handler to the IPA.
The best grid is then calculated to maximize the number of pixels taken
into account in each cells.
As commented in the source code, it can be improved, as it has (at least)
one limitation: if a cell is big (say 128 pixels wide) and indicated as
saturated, it won't be taken into account at all.
Maybe is it possible to have a smaller one, at the cost of a few pixels
to lose, in which case we can center the grid using the x_start and
y_start parameters.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Simplify name-spacing of the IPU3 components by placing it in the
ipa::ipu3 namespace directly.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The configure operation is synchronous and should not send events back
to the pipeline handler.
If information needs to be returned from configure it should be handled
through the interface directly.
Move the initial call to setControls() out of configure() and into the
start() method which is called after the IPA running_ state is updated.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The IPU3 IPA will need the BDS configuration when the AWB/AGC algorithm
will be integrated.
In order to do that, the configure() interface needs to be modified.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Setting a default EXPOSURE and ANALOGUE_GAIN makes sense for the first
frame but there is no need to force it for all frames.
It will be called later by the 3A algorithms.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Remove everything related to the C API, including ipa_context,
ipa_context_wrapper, and IPAInterfaceWrapper. Also remove relevant
documentation.
ipaCreate() provided by IPA implementations, and createInterface()
provided by IPAModule (wrapper around IPA implementation) both now
return a C++ object IPAInterface instead of struct ipa_context.
Although IPAInterfaceWrapper is the only component of libipa, the
skeleton and build files for libipa are retained.
After converting the C API to the C++-only API, make all pipeline
handlers and IPAs use the new API.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
This is a combination of 21 commits:
---
libcamera: IPAModule: Replace ipa_context with IPAInterface
With the new IPC infrastructure, we no longer need the C interface as
provided by struct ipa_context. Make ipaCreate_() and createInterface()
return IPAInterface.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: ipa_context_wrapper: Remove ipa_context_wrapper
Since ipa_context has been replaced with custom IPAInterfaces, it is not
longer needed. Remove it.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAInterface: remove ipa_context and functions from documentation
Remove all the documentation related to ipa_context and the C IPA API,
as well as the documentation about the functions in the IPAInterface.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
---
libcamera: IPAInterface: Remove all functions from IPAInterface
Now that all the functions in the IPA interface are defined in the data
definition file and a specialized IPAInterface is generated per pipeline
handler, remove all the functions from the base IPAInterface.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAInterface: make ipaCreate return IPAInterface
With the new IPC infrastructure, we no longer need the C interface as
provided by struct ipa_context. Make ipaCreate return IPAinterface.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
---
ipa: remove IPAInterfaceWrapper
As every pipeline has its own proxy, IPAInterfaceWrapper is no
longer necessary. Remove it.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
---
libcamera: IPAProxy: Remove stop() override
Since stop() is part of the IPA interface, and the IPA interface is now
generated based on the data definition file per pipeline, this no longer
needs to be overrided by the base IPAProxy. Remove it.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAProxy, IPAManager: Switch to one-proxy-per-pipeline scheme
IPAProxy is changed in two major ways:
- Every pipeline has its own proxy, to support each pipeline's IPA
interface
- IPAProxy implementations always encapsulate IPA modules, and switch
internally for isolation or threaded
The IPAProxy registration mechanism is removed, as each pipeline will
have its own proxy, so the pipeline can pass the specialized class name
of the IPAProxy to the IPAManager for construction.
IPAManager is changed accordingly to support these changes:
- createIPA is a template function that takes an IPAProxy class, and
always returns an IPAProxy
- IPAManager no longer decides on isolation, and simply creates an
IPAProxy instance while passing the isolation flag
Consequently, the old IPAProxy classes (IPAProxyThread and
IPAProxyLinux) are removed. The IPAInterfaceTest is updated to use
the new IPAManager interface, and to construct a ProcessManager as no
single global instance is created anymore.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
---
libcamera: IPAProxy: Add isolate parameter to create()
Since IPAProxy implementations now always encapsulate IPA modules, add a
parameter to create() to signal if the proxy should isolate the IPA or not.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAManager: Fetch IPAProxy corresponding to pipeline
Now that each pipeline handler has its own IPAProxy implementation, make
the IPAManager fetch the IPAProxy based on the pipeline handler name.
Also, since the IPAProxy is used regardless of isolation or no
isolation, remove the isolation check from the proxy selection.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
---
libcamera: IPAManager: add isolation flag to proxy creation
When the IPA proxy is created, it needs to know whether to isolate or
not. Feed the flag at creation of the IPA proxy.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAManager: Make createIPA return proxy directly
Since every pipeline knows the type of the proxy that it needs, and
since all IPAs are to be wrapped in a proxy, IPAManager no longer needs
to search in the factory list to fetch the proxy factory to construct a
factory. Instead, we define createIPA as a template function, and the
pipeline handler can declare the proxy type when it calls createIPA.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: IPAProxy: Remove registration mechanism
Implementations of IPA proxies use a registration mechanism to register
themselves with the main IPA proxy factory. This registration declares
static objects, causing a risk of things being constructed before the
proper libcamera facilities are ready. Since each pipeline handler has
its own IPA proxy and knows the type, it isn't necessary to have a proxy
factory. Remove it to alleviate the risk of early construction.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: proxy: Remove IPAProxyLinux and IPAProxyThread
We have now changed the proxy from per-IPC mechanism to per-pipeline.
The per-IPC mechanism proxies are thus no longer needed; remove them.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
tests: ipa_interface_test: Update to use new createIPA
Update the IPA interface test to use the new createIPA function from
IPAManager. Also create an instance of ProcessManager, as no single
global instance is created automatically anymore. Update meson.build to
to depend on the generated IPA interface headers.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: PipelineHandler: Remove IPA from base class
Since pipeline handlers now have their own IPA interface types, it can no
longer be defined in the base class, and each pipeline handler
implementation must declare it and its type themselves. Remove it from
the base class.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
ipa: raspberrypi: Add mojom data definition file
Add a mojom data definition for raspberrypi pipeline handler's IPAs.
This simplifies the API between the raspberrypi pipeline handler and the
IPA, and is not a direct translation of what was used before with
IPAOperationData.
Also move the enums from raspberrypi.h to raspberrypi.mojom
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: pipeline, ipa: raspberrypi: Use new data definition
Now that we can generate custom functions and data structures with mojo,
switch the raspberrypi pipeline handler and IPA to use the custom data
structures as defined in the mojom data definition file.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: pipeline, ipa: vimc: Support the new IPC mechanism
Add support to vimc pipeline handler and IPA for the new IPC mechanism.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
---
libcamera: pipeline, ipa: rkisp1: Support the new IPC mechanism
Add support to the rkisp1 pipeline handler and IPA for the new IPC
mechanism.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
libcamera: pipeline, ipa: ipu3: Support the new IPC mechanism
Add support to ipu3 pipeline handler and IPA for the new IPC mechanism.
[Original version]
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
[Fixed commit message and small changes]
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add an empty IPA skeleton for the IPU3 pipeline. The skeleton IPA
handles the flow of parameter and statistic buffers but does not read or
write anything in the buffers. It also allows the IPA to set sensor
controls but does not implement any logic to set optimal values and
instead sets the V4L2 exposure and gain controls to max and keeps them
at that setting.
This IPA is meant as a base to allow the pipeline handler to be wired up
to an IPA. The image algorithms can then later be added to the IPA
independently from also having to add plumbing to the pipeline handler.
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
