| Age | Commit message (Collapse) | Author |
|---|
|
Add support for planar YVU420.
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Remove use of vcsm allocations and replace with dma heap allocations.
The pipeline handler now passes the fd of the allocation over to the IPA
instead of the raw pointer.
Also use libcamera::FileDescriptor for fd lifetime management.
This commit must be built alongside the accompanying BCM2835 ISP kernel
driver changes at https://github.com/raspberrypi/linux/pull/3715.
Otherwise a mismatch will cause undefined behavior.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
To make error handling easier in callers, allow the stop() function to
be called when the proxy is already stopped, or not started yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
The IPA is meant to be started when starting the camera, and stopped
when stopping it. It was so far started early in order to handle the
IPAInterface::processEvent() call related to lens shading table
allocation before IPAInterface::configure() to pass the table to the
IPA. Now that the lens shading table is passed through configure(),
starting the IPA early isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
The Raspberry Pi IPA uses the custom RPI_IPA_ACTION_SET_SENSOR_CONFIG
frame action to send the sensor staggered write configuration to the
pipeline handler when the IPA is configured. Replace this ad-hoc
mechanism by passing the corresponding data back from the IPA to the
pipeline handler through the configure() response. This allows
synchronous handling of the response on the pipeline handler side.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
The IPAInterface::configure() function now accepts custom configuration
data. Use it to pass the lens shading table instead of using a custom
IPA event. This will allow starting the IPA when starting the camera,
instead of pre-starting it early in order to process the lens shading
table allocation event.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
The camera sensor orientation is now handled by the pipeline handler.
Drop hardcoded per-sensor orientations from the IPA.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
Instead of receiving sensor orientation configuration from the IPA,
retrieve it from the CameraSensor Rotation property, and configure the
HFLIP and VFLIP controls accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
The PipelineHandlerRPi::configureIPA() function accesses plenty of
member data from the RPiCameraData class and no member from the
PipelineHandlerRPi class. Move it to RPiCameraData where it logically
belongs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The controls parameter of StaggeredCtrl::set(), passed by reference, is
not modified by the function. Make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The controls variable in PipelineHandlerRPi::start() is unused. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
|
|
Add two new parameters, ipaConfig and result, to the
IPAInterface::configure() function to allow pipeline handlers to pass
custom data to their IPA, and receive data back. Wire this through the
code base. The C API interface will be addressed separately, likely
through automation of the C <-> C++ translation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
A comment copied from the IPAInterfaceWrapper incorrectly mentions the
IPAInterfaceWrapper class instead of the IPAContextWrapper class. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The parameters to the configure() function part of the ipa_context_ops
are not documented. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a file is opened in WriteOnly or ReadWrite mode, create it if it
doesn't exist.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Add basic support to read and write data from/to a file, along with
retrieving and setting the current read/write position.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add alignDownTo(), alignUpTo(), boundTo() and expandTo() helper
functions to the Size class. These are in-place versions of the existing
alignedDownTo(), alignedUpTo(), boundedTo() and expandedTo() functions.
The new helpers return a reference to the size, to allow chaining the
functions. One can thus write
size.alignDownTo(16, 16).alignUpTo(32, 32)
.boundTo({ 40, 80 }).expandTo({ 16, 80 });
instead of
size.alignDownTo(16, 16);
size.alignUpTo(32, 32);
size.boundTo({ 40, 80 });
size.expandTo({ 16, 80 });
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
SizeRange is defined as a class while Size and Rectangle are defined as
struct. This is confusing for users in forward declarations. Simplify it
by turning both structures into classes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Rectangle, unlike Size, has no constructor, requiring the users to
explicitly initialize the instances. This is error-prone, add
constructors.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
A subsequent change to the Rectangle will require the definition of the
Size to be available. Define Rectangle after Size to ease review of that
change. No code change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Size has a default constructor, there's no need to default-initialize
instances explicitly. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Prior to N4387 ([1]), the std::tuple::tuple(const Types&...) constructor
was unconditionally explicit. gcc 5 doesn't implement N4387, leading to
a compilation error in the simple pipeline handler. Use
std::make_tuple() to fix it.
[1] http://www.open-std.org/jtc1/sc22/wg21/docs/papers/2015/n4387.html
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Pipeline handlers commonly have to calculate the minimum or maximum of
multiple sizes, or align a size's width and height. Add helper functions
to the Size class to perform those tasks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
Use std::numerical_limits to initialise the best score instead of an
arbitrary value. This fixes a failure in v4l2-conformance when using
the Raspberry Pi pipeline handler and v4l2-compatibility libcamera
layer.
Reported-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
|
|
For handling try_fmt, the values should be filled in by validating the
stream configuration, and not by recalculating them or manually checking
against the cached list of formats and sizes. Add a new
V4L2Camera::validateConfiguration() function to validate a configuration
and use it to obtain size, format, stride, and frameSize values.
If the format negotiation fails, return error from try_fmt and s_fmt.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The stride and frameSize should be obtained through StreamConfiguration
rather than PixelFormatInfo, as pipeline handlers might have different
values (eg. for alignment). Get the stride and frameSize values from
StreamConfiguration instead of from PixelFormatInfo.
This removes the need for V4L2CameraProxy's calculation helper functions
(bplMultiplier, imageSize, v4l2ToDrm, drmToV4L2, calculateSizeImage) and
formats, so remove them.
This also removes the need for V4L2CameraProxy::calculateSizeImage, so
remove it,.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The buffer operations in V4L2Camera were getting the stream from the
wrong place. Fix it.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Now that all the pipeline handlers fill in the stride information at
validation time, update the documentation accordingly.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Fill the stride and frameSize fields of the StreamConfiguration at
configuration validation time instead of at camera configuration time.
This allows applications to get the stride when trying a configuration
without modifying the active configuration of the camera.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Unsupported formats should not be added to the configuration when
generating the configuration. Filter them out.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Unsupported formats should not be added to the configuration when
generating the configuration. Filter them out.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Pipeline handlers must acquire media devices via
PipelineHander::acquireMediaDevice so that the media devices can be
registered with the pipeline handler, so that they can be automatically
added to the devnum map for the v4l2 compatibility layer to use. Die
fatally if any camera trying to be registered has not acquired any media
devices via acquireMediaDevice.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Media devices should be acquired by pipeline handlers via
PipelineHandler::acquireMediaDevice so that the media devices can be
registered in the pipeline handler so that they can be automatically
added to the devnum map for the v4l2 compatibility layer to use. Make
the raspberrypi pipeline handler do this.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Simplify code for looking up PixelFormatInfo using a V4L2 format by
using the new PixelFormatInfo lookup function based on V4L2 format.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add member functions to PixelFormatInfo for calculating stride and frame
size. This will simplify existing code that calculates these things.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In addition to the stride field, we want the pipeline handler to be able
to declare the frame size for the configuration. Add a frameSize field
to StreamConfiguration for this purpose.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add a lookup function for PixelFormatInfo that takes a V4L2PixelFormat.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add tryFormat and its variations (meta, single-plane, multi-plane) to
V4L2VideoDevice.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Packed formats make it difficult to calculate stride as well as
frame size with the fields that PixelFormatInfo currently has.
bitsPerPixel is defined as the average number of bits per pixel, and
only counts effective bits, so it is not useful for calculating
stride and frame size.
To fix this, we introduce a concept of a "pixel group". The size of this
group is defined as the minimum number of pixels (including padding)
necessary in a row when the image has only one column of effective
pixels. The pixel group has one more attribute, that is the "bytes per
group". This determines how many bytes one pixel group consumes. These
are the fields pixelsPerGroup and bytesPerGroup that are defined in this
patch. Defining these two values makes it really simple to calculate
bytes-per-line, as ceil(width / pixelsPerGroup) * bytesPerGroup, where
width is measured in number of pixels. The ceiling accounts for padding.
The pixel group has another contraint, which is that the pixel group
(bytesPerGroup and pixelsPerGroup) is the smallest repeatable unit. What
this means is that, for example, in the IPU3 formats, if there is only
one column of effective pixels, it looks like it could be fit in 5 bytes
with 3 padding pixels (for a total of 4 pixels over 5 bytes). However,
this unit is not repeatable, as at the 7th group in the same row, the
pattern is broken. Therefore, the pixel group for IPU3 formats must be
25 pixels over 32 bytes.
Clearly, pixelsPerGroup must be constant for all planes in the format.
The bytesPerGroup then, must be a per-plane attribute. There is one more
field, verticalSubSampling, that is per-plane. This is simply a divider,
to divide the number of rows of pixels by the sub-sampling value, to
obtain the number of rows of pixels for the subsampled plane.
For example, for something simple like BGR888, it is self-explanatory:
the pixel group size is 1, and the bytes necessary is 3, and there is
only one plane with no (= 1) vertical subsampling. For YUYV, the
CbCr pair is shared between two pixels, so even if you have only one
pixel, you would still need a padded second Y, therefore the pixel
group size is 2, and bytes necessary is 4 (as opposed to 1 and 2). YUYV
also has no vertical subsampling. NV12 has a pixel group size of 2
pixels, due to the CbCr plane. The bytes per group then, for both
planes, is 2. The first plane has no vertical subsampling, but the
second plane is subsampled by a factor of 2.
The IPU3 formats are also self-explanatory, as they are single-planar,
and have a pixel group size of 25, consuming 32 bytes. Although a
comment in the driver suggests that it should be 50 and 64,
respectively, this is an attribute of the driver, and not the format, so
this shall be set by the ipu3 pipeline handler.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Add formats for NV24 and NV42. While at it, reorder the NV formats so
that NV12 and NV21 come first, followed by NV16, NV61, NV24, and NV42.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Use a helper instead of local code to retrieve all keys from a map.
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add a map_keys() function to the utils namespace to extract keys from a
map.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Niklas: change return type to std::vector instead of std::set]
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Use the new Size::isNull() function through the code base to replace
manual checks. While the new code isn't equivalent, as isNull() checks
that both width and height are zero, it catches the same conditions in
practice.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Umang Jain <email@uajain.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
A capture request is no longer limited to a single output buffer.
Remove the limitation, but (for now) keep the check to ensure that
at least one buffer is always provided.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Construct a FrameBuffer for every buffer given in the camera3Request
and add it to the libcamera Request on the appropriate stream.
The correct stream is obtained from the private data of the camera3_stream
associated with the camera3_buffer.
Comments regarding supporting only one buffer are now removed, and
FrameBuffers have their lifetime tracked in the Camera3RequestDescriptor
to ensure they are released when the Request is completed.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
