| Age | Commit message (Collapse) | Author |
|---|
|
Fix an error message typo s/static/result/.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Since meson v0.49.0, join_paths() is equivalent to '/' hence,
drop and replace it with '/' short-hand in meson files.
This commit does not introduce any functional changes.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The controller algorithms currently run on every frame provided to the
IPA by the pipeline handler. This may be undesirable for very fast fps
operating modes where it could significantly increase the computation
cycles (per unit time) without providing any significant changes to the
IQ parameters. The added latencies could also cause dropped frames.
Pass the FrameBuffer timestamp to the IPA through the controls. This
timestamp will be used to rate-limit the controller algorithms to run
with a minimum inter-frame time given by a compile time constant,
currently set to 16.66ms. On startup, we don't rate-limit the algorithms
until after the number of frames required for convergence.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a new Merge method to the Metadata class. This will merge all unique
key/value pairs from a source metadata map to the destination map.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Add a default, move and copy constructor as well as a move operator
implementation RPiController::Metadata class.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Replace std::lock_guard with std::scoped_lock. When locking a single
mutex, both are functionally the same. When locking two mutexes in the
operator= overload, the scoped_lock uses a deadlock avoidance algorithm
to avoid deadlock.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Rearrange header includes to be in alphabetical order.
Add whitespace to class definition to match libcamera coding guidelines.
Fix a typo in the comment showing an example of scoped locks.
There are no functional changes in this commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Store the number of dropped frames on startup in a member variable. This
will be used in a subsequent change for rate limiting the controller
algorithms.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
change
The Raspberry Pi pipeline handler does not update the sensor format
using CameraSensor::setFormat(), so it must manually force the update of
the associated ControlInfoMap.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The minimum and maximum vblanking can change when a new format is
applied to the sensor subdevice, so be sure to retrieve up-to-date
values.
The V4L2Device acquires the new updateControlInfo() method to perform
this function, and which the CameraSensor calls automatically if its
setFormat method is used to update the sensor.
However, not all pipeline handlers invoke the setFormat method
directly, so the new method must be made publicly available for
pipeline handlers to call if they need to.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Calculate the value of the ANDROID_SENSOR_INFO_PHYSICAL_SIZE property
multiplying the number of sensor's readable pixels with the pixel unit
cell size if provided by the Camera.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Register static properties in the CameraSensor class by inspecting the
camera sensor properties database.
Static properties are overridden by properties retrieved from
the kernel interface at run-time if any overlap between the two
sets occurs.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Introduce a database of camera sensor properties, which contains
information on the camera sensor which are not possible, or desirable,
to retrieve from the device at run time.
The camera sensor database is accessed through a static function and
is indexed using the camera sensor model as reported by
properties::Model.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
CamHelpers get virtual Prepare() and Process() methods, running just
before and just after the ISP, just like Raspberry Pi Algorithms.
The Prepare() method is able to parse the register dumps in embedded
data buffers, and can be specialised to perform custom processing when
necessary.
The IPA itself only needs to call the new Prepare() and Process()
methods. It must fill in the DeviceStatus from the controls first, in
case the Prepare() method does not supply its own values.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Improve MdParser::Parse() by taking a Span, pointing to const data
that it should not change, as its input buffer.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The ControlList merge operation is protected with an ASSERT to guarantee
that the two lists are compatible.
Unfortunately this assertion fails when we run IPAs in an isolated case
as while the lists are compatible, the isolated IPA has a unique
instance of the id map. This breaks the pointer comparison, and the
assertion fails with a false positive.
Remove the assertion, leaving only a todo in it's place as this breaks
active users of the library.
Bug: https://bugs.libcamera.org/show_bug.cgi?id=31
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Use the controls::SensorTimestamp value to populate
ANDROID_SENSOR_TIMESTAMP result metadata.
The Camera is assumed to provide the control in the Request metadata.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Implement support for the new '--metadata' option by printing the
value of each metadata entry associated with a completed Request.
As sample of the output, running on raspberry pi, looks like the
following:
3050.205672 (30.01 fps) stream0 seq: 000033 bytesused: 720000
ScalerCrop = (0x2)/3280x2460
ExposureTime = 13969
AeLocked = true
DigitalGain = 1.000721
Lux = 771.204224
ColourGains = [ 1.561101, 1.629698 ]
ColourTemperature = 4289
SensorBlackLevels = [ 4096, 4096, 4096, 4096 ]
ColourCorrectionMatrix = [ 1.691066, -0.599756, -0.091317, -0.437452, 1.983766, -0.546314, -0.083429, -0.722407, 1.805836 ]
AnalogueGain = 2.000000
SensorTimestamp = 3050205672000
3050.238999 (30.01 fps) stream0 seq: 000034 bytesused: 720000
ScalerCrop = (0x2)/3280x2460
ExposureTime = 13969
AeLocked = true
DigitalGain = 1.000709
Lux = 771.232422
ColourGains = [ 1.560868, 1.630029 ]
ColourTemperature = 4289
SensorBlackLevels = [ 4096, 4096, 4096, 4096 ]
ColourCorrectionMatrix = [ 1.691081, -0.599726, -0.091362, -0.437497, 1.983627, -0.546130, -0.083420, -0.722523, 1.805943 ]
AnalogueGain = 2.000000
SensorTimestamp = 3050238999000
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add the "--metadata" option to the cam tool, which will be used to
print the metadata associated with a completed capture request.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata by using the
Unicam::Image buffer timestamp as an initial approximation.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition, but when used
to compare two consecutive frames it gives an acceptable estimation of
the sensor frame period duration.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
the metadata associated with the Request are over-written, deleting
the information set at output buffer completion, such as the
SensorTimestamp.
This commit applies to the RaspberryPi pipeline handler the same change
applied to IPU3 in commit 2ee3dd57e2fc ("libcamera: ipu3: Merge IPA
metadata controls").
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
I got fooled by the documentation of setRequest() implying that the
function is meant to be called by pipeline handlers only, which it is
used in the Request class at Request::addBuffer() and Request::reuse()
time.
Rework the documentation to report that.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp reports the video capture buffer processing time,
and it does not theoretically matches the 'start of exposure'
definition.
VIMC being a testing platform and the test driver completes the buffers
for each media entity connected in the pipeline one after the other, the
current solution is acceptable for the pipeline.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition. Record this with
a \todo entry.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition. Record this with
a \todo entry.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
the metadata associated with the Request are over-written, deleting
the information set at output buffer completion, such as the
SensorTimestamp.
This commit applies to the RkISP1 pipeline handler the same change
applied to IPU3 in commit 2ee3dd57e2fc ("libcamera: ipu3: Merge IPA
metadata controls").
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The UVC driver reports timestamps of SOE event through metadata, for
which there is no support in the current pipeline implementation.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
they should be merged with the metadata set by the pipeline handler
before reporting them to applications.
Use ControlList::merge() to collect the IPA produced controls to the
request's metadata.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata by using the
CIO2 buffer timestamp as an initial approximation.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition, but when used
to compare two consecutive frames it gives an acceptable estimation of
the sensor frame period duration.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Destage the 'SensorTimestamp' control, which is used by pipeline
handlers to report the time when the first active line of the sensor's
pixel array is exposed.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add a new ControlList::merge() function to merge two control lists by
copying in the values in the list passed as parameters.
This can be used by pipeline handlers to merge metadata they populate
with metadata received from an IPA.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[reimplement the function by not using std::unordered_map::merge()]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
libcamera internal headers are not installed system-wide. Hence, any
inclusion of internal headers should follow the #include directive
form:
#include "libcamera/internal/header.h"
This was not the case for a few of the class in android HAL. Fix them.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add a check, that makes sure that the given FrameBuffer is associated
to a RkISP1FrameInfo instance. The current code tries to access the
frame info without checking if it actually exists.
Fixes: 0eb65e14e ("libcamera: pipeline: rkisp1: Attach to an IPA")
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Define libcamera specific system paths for use within the library code
base. These can be used to identify system configuration files and
shared data.
Also, make use of the new system path variables and map the ipa paths
upon the libcamera system path, making use of the new shorter syntax for
join_paths().
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Sensors provide embedded data buffers and not metadata buffers,
replace the incorrect term with the correct one.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Fix two typos and improve the sentence.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
V4L2Device::updateControls() takes two arguments, raw array and
its size, for the v4l2_ext_control values. This replaces it with
libcamera::Span.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The original code uses Variable-Length-Array, which is not
officially supported in C++. This replaces the array with
std::vector.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The original code uses Variable-Length-Array, which is not officially
supported in C++. This replaces the array with std::vector.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Simplify name-spacing of the RKISP1 components by placing it in the
ipa::rkisp1 namespace directly.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
When the CIO2 returns a cancelled buffer, we will not queue buffers
to the IMGU.
These buffers should be explicitly marked as cancelled to ensure
the application knows there is no valid metadata or frame data
provided in the buffer.
Provide a cancel() method on the FrameBuffer to allow explicitly
cancelling a buffer.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The RkISP1FrameInfo structure associated data sent to the IPA and is
essential for handling events.
If it can not be found, this is a fatal error which must be fixed.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The FrameInfo structure associates the data sent to the IPA
and is essential for handling events.
If it can not be found, this is a fatal error which must be fixed.
While we're changing the line, also correct a spelling error for
'Information'.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
When the camera manager calls stop on a pipeline, it is expected that
the pipeline handler guarantees all requests are returned back to the
application before the camera has stopped.
Ensure that this guarantee is met by providing an accessor on the
pipeline handler to validate that all pending requests are removed.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The BNR configuration structure has inconsistent initialisation of two
members.
This was picked up by Coverity, after merge.
While this code is still functional, fix them to be consistent with the
other initialisations within the struct.
Reported-by: Coverity CID=320056
Reported-by: Coverity CID=320058
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Implement basic auto-exposure (AE) and auto-gain (AG) correction functions.
The functions computeTargetExposure() and computeGain() are adapted from
the Raspberry Pi AGC implementation to suit the IPU3 structures, and
filtering is added to reduce visible stepsize when there are large
exposure changes.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The IPA will locally modify the parameters before they are passed down
to the ImgU. Use a local parameter object to give a reference to those
algorithms.
Inherit from the Algorithm class to implement basic AWB functions.
The configure() call will set exposure and gain to their minimum value,
so while AGC is not there, the frames will be dark.
Once AWB is done, a color temperature is estimated and a default CCM matrix
will be used (yet to be tuned).
Implement a basic "grey-world" AWB algorithm just for demonstration purpose.
The BDS output size is passed by the pipeline handler to the IPA.
The best grid is then calculated to maximize the number of pixels taken
into account in each cells.
As commented in the source code, it can be improved, as it has (at least)
one limitation: if a cell is big (say 128 pixels wide) and indicated as
saturated, it won't be taken into account at all.
Maybe is it possible to have a smaller one, at the cost of a few pixels
to lose, in which case we can center the grid using the x_start and
y_start parameters.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
This class will be used at least by AGC algorithm when quantiles are
needed for example. It stores a cumulative frequency histogram. Going from
cumulative frequency back to per-bin values is a single subtraction, while
going the other way is a loop.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
In order to instantiate and use algorithms (AWB, AGC, etc.)
there is a need for a common class to define mandatory methods.
Instead of reinventing the wheel, reuse what Raspberry Pi has done and
adapt to the minimum requirements expected.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
It's valid for a camera to return a nullptr if the requested set of
roles can not be satisfied. This is not correctly handled by
lc-compliance which instead crashes, fix this.
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
|
