| Age | Commit message (Collapse) | Author |
|---|
|
The controller algorithms currently run on every frame provided to the
IPA by the pipeline handler. This may be undesirable for very fast fps
operating modes where it could significantly increase the computation
cycles (per unit time) without providing any significant changes to the
IQ parameters. The added latencies could also cause dropped frames.
Pass the FrameBuffer timestamp to the IPA through the controls. This
timestamp will be used to rate-limit the controller algorithms to run
with a minimum inter-frame time given by a compile time constant,
currently set to 16.66ms. On startup, we don't rate-limit the algorithms
until after the number of frames required for convergence.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
change
The Raspberry Pi pipeline handler does not update the sensor format
using CameraSensor::setFormat(), so it must manually force the update of
the associated ControlInfoMap.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Report the sensor's timestamp in the Request metadata by using the
Unicam::Image buffer timestamp as an initial approximation.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition, but when used
to compare two consecutive frames it gives an acceptable estimation of
the sensor frame period duration.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
the metadata associated with the Request are over-written, deleting
the information set at output buffer completion, such as the
SensorTimestamp.
This commit applies to the RaspberryPi pipeline handler the same change
applied to IPU3 in commit 2ee3dd57e2fc ("libcamera: ipu3: Merge IPA
metadata controls").
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp reports the video capture buffer processing time,
and it does not theoretically matches the 'start of exposure'
definition.
VIMC being a testing platform and the test driver completes the buffers
for each media entity connected in the pipeline one after the other, the
current solution is acceptable for the pipeline.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition. Record this with
a \todo entry.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition. Record this with
a \todo entry.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
the metadata associated with the Request are over-written, deleting
the information set at output buffer completion, such as the
SensorTimestamp.
This commit applies to the RkISP1 pipeline handler the same change
applied to IPU3 in commit 2ee3dd57e2fc ("libcamera: ipu3: Merge IPA
metadata controls").
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata using the
completed buffer timestamp.
The UVC driver reports timestamps of SOE event through metadata, for
which there is no support in the current pipeline implementation.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
When a Request is completed upon receiving the IPA produced metadata,
they should be merged with the metadata set by the pipeline handler
before reporting them to applications.
Use ControlList::merge() to collect the IPA produced controls to the
request's metadata.
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Report the sensor's timestamp in the Request metadata by using the
CIO2 buffer timestamp as an initial approximation.
The buffer's timestamp is recorded at DMA-transfer time, and it does not
theoretically matches the 'start of exposure' definition, but when used
to compare two consecutive frames it gives an acceptable estimation of
the sensor frame period duration.
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add a check, that makes sure that the given FrameBuffer is associated
to a RkISP1FrameInfo instance. The current code tries to access the
frame info without checking if it actually exists.
Fixes: 0eb65e14e ("libcamera: pipeline: rkisp1: Attach to an IPA")
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
When the CIO2 returns a cancelled buffer, we will not queue buffers
to the IMGU.
These buffers should be explicitly marked as cancelled to ensure
the application knows there is no valid metadata or frame data
provided in the buffer.
Provide a cancel() method on the FrameBuffer to allow explicitly
cancelling a buffer.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The RkISP1FrameInfo structure associated data sent to the IPA and is
essential for handling events.
If it can not be found, this is a fatal error which must be fixed.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The FrameInfo structure associates the data sent to the IPA
and is essential for handling events.
If it can not be found, this is a fatal error which must be fixed.
While we're changing the line, also correct a spelling error for
'Information'.
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
s/embedded/bayer/
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The ipa_->init() method can fail if the IPA can't load correctly.
This should be caught by the pipeline handler to prevent continuing
with an invalid IPA.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Previously when a frame got cancelled, the frameInfo flags
metadataProcessed and paramDequeued wouldn't get set, meaning that the
request wasn't able to be completed and cancelled.
Make sure that these flags are set when the frame gets cancelled so that
the request can be cancelled.
This issue happened while running lc-compliance.
Suggested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
frameInfo
Assert that there are no queued requests before clearing the frameInfo,
otherwise a SEGFAULT can occur.
This issue happened while running lc-compliance.
Suggested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
The IPA should be stopped before stopping the streams in order to avoid
a "No BufferCache available to queue" issue.
This issue happened while running lc-compliance.
Suggested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
|
|
When seting up the pipeline, the latest entity in the queue is
taken but the oldest one is poped. This is a mistake. Fix it.
Fixes: 4671911df040 ("pipeline: simple: Use breadth-first search to setup media pipeline")
Signed-off-by: Phi-Bang Nguyen <pnguyen@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The comment states, that we get the device format to pass it to the IPA,
but the variable `sensorFormat` is not used again after it's assignment.
Remove it, together with the comment.
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
For all frame indexes, use the same sequence number as generated
by the Request object.
This allows clear matching of what operations occurred to which request.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Fix two simple typos.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
|
|
A range-based for loop whose range expression is an array of char
pointers and range variable declaration is a const reference to a
std::string creates a temporary string from the char pointer and binds
the range variable reference to it. This creates a const reference to a
temporary, which is valid in C++, and extends the lifetime of the
temporary to the lifetime of the reference.
However, lifetime extension in range-based for loops is considered as a
sign of a potential issue, as a temporary is created for every
iteration, which can be costly, and the usage of a reference in the
range declaration doesn't make it obvious that the code isn't simply
binding a reference to an existing object. gcc 11, with the
-Wrange-loop-construct option, flags this:
uvcvideo.cpp:432:33: error: loop variable 'name' of type 'const string&' {aka 'const std::__cxx11::basic_string<cha
r>&'} binds to a temporary constructed from type 'const char* const' [-Werror=range-loop-construct]
| 432 | for (const std::string &name : { "idVendor", "idProduct" }) {
| | ^~~~
To please the compiler, make the range variable a const char *. This may
bring a tiny performance improvement, as the name is only used once, in
a location where the compiler can use
operator+(const std::string &, const char *)
instead of
operator+(const std::string &, const std::string &)
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Use a const char * type instead of auto, and update the commit message
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
s/Will need to/We'll need to/
Signed-off-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Ensure that the buffers are associated with the request even if they are
used internally to be able to correctly map back to the resources they
are being used to fulfil.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Ensure that checks on resource availability are handled first, and then
operate on the queues only after the resources are confirmed as
available.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
When the imguOutputBufferReady() detects a cancelled frame, it is
reporting that the metadata has been processed in order to be able to
complete the cancelled request.
This causes the FrameInfo to be completed and deleted early, but then an
active buffer on the IMGU can complete and be unable to find the
FrameInfo for it to complete correctly.
Do not mark metadataProcessed early on the event that a single buffer is
detected as cancelled. The stopping of the V4L2 devices will ensure
that all queued buffers are returned to us and we can follow the normal
and expected shutdown sequence.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
The IPA should be stopped before the hardware devices to ensure that
all asynchronous actions have completed within the IPA before resources
are removed and released.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Rename ConfigInput to IPAConfig to be more consistent with the naming,
and remove ConfigInput::op, as it is never used.
Replace ConfigOutput with a ControlList type, as that is the only return
type from ipa::configure().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Separate out the in and out parameters in ipa::start() as they are not
the same. This function now takes in a ControlList and returns out a
struct StartConfig which holds a ControlList and drop frame count for
the pipeline handler to action.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Conditionally open the embedded data node in pipeline_handler::match()
based on whether the ipa::init() result reports if the sensor supports
embedded data or not.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Move the opening of the CamHelper from ipa::configure() to ipa::init().
This allows the pipeline handler to get the sensor specific parameters
in pipeline_handler::match() where the ipa is initialised.
Having the sensor parameters available earlier will allow selective
use of the embedded data node in a future change.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Pass the sensor model string to the IPA init() method through the
IPASettings structure.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
After commit 4671911df040 ("pipeline: simple: Use breadth-first search
to setup media pipeline"), the explanation in the SimplePipeline
documentation how the handler tries to find a valid path to capture
device does not reflect the reality anymore. Update the text to the new
situation.
Fixes: 4671911df040 ("pipeline: simple: Use breadth-first search to setup media pipeline")
Signed-off-by: Marian Cichy <m.cichy@pengutronix.de>
Reviewed-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The IPU3 IPA will need the BDS configuration when the AWB/AGC algorithm
will be integrated.
In order to do that, the configure() interface needs to be modified.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
IPA was configured after all the pipeline devices were started,
including IPA itself.
Move it at the end of configure() call.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
When the SimplePipeline is setting up its data and media pipeline in the
SimpleCameraData constructor, it merely tries to find the first valid
pad and link to the next entity, starting from the camera sensor.
Following this path may not always lead to a valid capture device and
therefore the setup will fail on some machines. This is for example an
issue when using the SimplePipeline on an i.MX-6Q with its i.MX IPU.
This commit implements a different approach to setup the media-pipeline
by finding the shortest path to a valid capture device, using the
breadth-first search algorithm. On i.MX6Q, the shortest path has a good
chance to be the path from the sensor to the CSI capture device, as
other paths may involve image converters, encoders or other IPU blocks
and will have therefore more nodes.
Signed-off-by: Marian Cichy <m.cichy@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
If the ISP::Output0 stream has not been configured, we must enable it
with a default format and resolution for internal use. This is to allow
the pipeline handler data flow to be consistent, and allow the IPA to
receive statistics for the frame.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
It is possible for the application to call pipeline_handler::configure()
multiple times, which would attempt to open the Unicam embedded data
node on every call. This would cause a warning message as the node
would have already been opened. Avoid this by tracking if the node
has previously been opened.
Note that this is a temporary fix since the open call for the Unicam
embedded data node will be moved from pipeline_handler::configure() to
pipeline_handler::match().
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
If an exposure time change adjusts the vblanking limits, and we set both
VBLANK and EXPOSURE controls through the VIDIOC_S_EXT_CTRLS ioctl, the
latter may fail if the value is outside of the limits calculated by the
old VBLANK value. This is a limitation in V4L2 and cannot be fixed by
setting VBLANK before EXPOSURE in a single VIDIOC_S_EXT_CTRLS ioctl.
The workaround here is to have the DelayedControls object mark the
VBLANK control as "priority write", which then write VBLANK separately
from (and ahead of) any other controls. This way, the sensor driver will
update the EXPOSURE control with new limits before the new values is
presented, and will thus be seen as valid.
To support this, a new struct DelayedControls::ControlParams is used in
the constructor to provide the control delay value as well as the
priority write flag.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Tested-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
[Kieran: Fix up trivial comments, merge conflicts]
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
In kernel 5.11 the rkisp1 uapi had changed to support different hardware
revisions. Currently only revision 10 is supported by the rkisp1 IPA and
therefore 'init' should fail if the revision is not 10.
This changes depends on the kernel driver reporting the hardware
revision, and thus requires the rkisp1 driver from v5.11 or newer.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The IPA of rkisp1 relies on some of the camera's controls.
Therefore it can't work if those controls are not given.
Return -EINVAL from 'configure' in that case.
Also return error from the pipeline's 'configure' method
if the IPA configure fails.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Register the FrameDurations control in the IPU3 pipeline handler
computed using the vertical blanking limits and the sensor
pixel rate as parameters.
The FrameDurations control limits should be updated everytime a new
configuration is applied to the sensor.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
The controls' limits initialized by the IPU3 pipeline handler depend
on the sensor configuration. In order to compute controls using a known
state apply to the sensor a configuration equal to its own resolution.
Move the \todo note regarding the controls' limits dependency on the
sensor configuration at the beginning of the function and remove the
other redundant ones in the function body.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Now that we support returning int directly in addition to other output
parameters, improve the configure() function in the raspberrypi IPA
interface.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The name vblankDelay is clearer.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
When the IPU3Frames completes, it deletes the internal info storage.
This storage contains the pointer to the Request, but in some cases the
pointer was being accessed after the info structure was removed.
Ensure that the Request is obtained before attempting to complete to
obtain a valid pointer.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Fix trivial spelling mistake.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
