| Age | Commit message (Collapse) | Author |
|---|
|
Fix up a few locations where we call notify_one() with the lock
held. In particular, restartAsync does not need to be called with the
lock held for its entire duration.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
In the libcamera framework, SwitchMode (which overwrites the
camera_mode) cannot run concurrently with Prepare (which uses it).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Switch FocusStatus::num to unsigned int for convenience.
Fill in libcamera::controls::FocusFoM with the average of the middle two
regions (across a 4x3 grid) FoM statistics from the ISP.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Previously, output of the focus measure could not be enabled without
recompiling (because of the RPI_LOGGING_ENABLE macro). This uses the
libcamera logging mechanism instead, so can be enabled/disabled at
runtime.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Adds FocusStatus to the image metadata, containing contrast measurements
across the image. Optionally also prints a contrast measure to the
console, to aid in manual adjustment of the lens. Note that it is not an
actual auto-focus algorithm that can drive a lens!
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The sharpness control is, loosely speaking, a gain applied to
the amount of sharpening added to an image. We also report the
sharpness setting used back to the caller in metadata.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
No need for it to be std::atomic as SwitchMode runs synchronously with
Prepare.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
mode changes
This commit causes the AGC to recalculate its camera exposure/gain
values when the camera mode changes. For example it's possible
that the exposure profile could be changed by the application so
the division between exposure time and analogue gain may be
different.
The other underlying reason (and which this commit accomplishes too)
is that the sensor's line timing may change in a new mode, and because
V4L2 drivers store a number of exposure _lines_, the resulting _time_
will "change under our feet". So we have to go through the process of
recalculating the correct number of lines and writing this back to the
sensor with every mode switch, regardless of anything else.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
This commit adds a Metadata parameter to the SwitchMode method
enabling it to return camera and other settings to the caller
(usually the configure method, just after the camera mode has been
selected).
In future this will allow the Raspberry Pi IPAs to take those settings
(such as exposure and analogue gain) and program them directly into
the camera or ISP before the camera is even started.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Initial implementation of the Raspberry Pi (BCM2835) libcamera IPA and
associated libraries.
All code is licensed under the BSD-2-Clause terms.
Copyright (c) 2019-2020 Raspberry Pi Trading Ltd.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
