summaryrefslogtreecommitdiff
path: root/src/ipa/raspberrypi/data
AgeCommit message (Collapse)Author
2021-05-11meson: Replace obselete join_paths() with '/' operatorUmang Jain
Since meson v0.49.0, join_paths() is equivalent to '/' hence, drop and replace it with '/' short-hand in meson files. This commit does not introduce any functional changes. Signed-off-by: Umang Jain <umang.jain@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
2021-03-14ipa: raspberrypi: Add support for imx327-based SE327M12 moduleDavid Plowman
This patch adds support for the Soho Enterprises SE327M12 module. The sensor is an imx327 which therefore uses the imx290 kernel driver and CamHelper. To use this module and camera tuning, place the following in the /boot/config.txt file: dtoverlay=imx290,clock-frequency=37125000 and then the existing imx290.json file must be over-written with se327m12.json Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2021-03-09ipa: raspberrypi: Add support for imx290/imx327 sensorsDavid Plowman
imx290 and imx327 share the same kernel driver (imx290.c) and are therefore both recognised here as "imx290". We add the necessary CamHelper for these sensors, as well as a camera tuning file. The tuning was done with an Innomaker STARVIS IMX327LQR module. These have no IR cut filter so there is no proper colour tuning. However, you should obtain reasonable results for most modules using this sensor. Specific tunings for further modules can always be added subsequently. To use this sensor on the Raspberry Pi platform, please add dtoverlay=imx290,clock-frequency=74250000 into your /boot/config.txt file. Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2021-01-20ipa: raspberrypi: config: Update shutter speeds for imx219/477 and ov5647Naushir Patuck
Set the maximum shutter speed for the normal exposure profile to 66ms, allowing viewfinder framerates to go down to approx. 15fps. Set the maximum shutter speed for the sport exposure profile to 33ms, limiting the minimum framerate to approx. 30fps. Add a long exposure profile to allow shutter speeds of up to 120ms. Signed-off-by: Naushir Patuck <naush@raspberrypi.com> Reviewed-by: David Plowman <david.plowman@raspberrypi.com> Tested-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2020-12-01src: ipa: raspberrypi: Fix initial AGC oscillation for imx219 sensorDavid Plowman
The exposure times in the exposure modes were causing AGC oscillations because the algorithm was demanding long unachievable exposure times but, without working sensor metadata, thought it was getting them when actually it was not. We fix it by making the exposure profile request only achievable exposure times, as we do for the ov5647 tuning. Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Naushir Patuck <naush@raspberrypi.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2020-11-20src: ipa: raspberrypi: Change 'sport' exposure mode name to 'short'David Plowman
The names have to match for the setting to work. Use the libcamera terminology for consistency (even though it touches more files). Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Naushir Patuck <naush@raspberrypi.com> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
2020-07-03ipa: raspberrypi: Enable focus measure without recompileDavid Plowman
Previously, output of the focus measure could not be enabled without recompiling (because of the RPI_LOGGING_ENABLE macro). This uses the libcamera logging mechanism instead, so can be enabled/disabled at runtime. Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2020-06-25ipa: rpi: Add "focus" algorithmDavid Plowman
Adds FocusStatus to the image metadata, containing contrast measurements across the image. Optionally also prints a contrast measure to the console, to aid in manual adjustment of the lens. Note that it is not an actual auto-focus algorithm that can drive a lens! Signed-off-by: David Plowman <david.plowman@raspberrypi.com> Signed-off-by: Naushir Patuck <naush@raspberrypi.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
2020-06-09libcamera: Add missing SPDX headers to miscellaneous small filesLaurent Pinchart
Add missing SPDX headers to miscellaneous small files. Use CC0-1.0 for meson.build, .gitignore and the small include/linux/README, and licenses matching the corresponding component for other files. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
2020-05-11libcamera: ipa: Raspberry Pi IPANaushir Patuck
Initial implementation of the Raspberry Pi (BCM2835) libcamera IPA and associated libraries. All code is licensed under the BSD-2-Clause terms. Copyright (c) 2019-2020 Raspberry Pi Trading Ltd. Signed-off-by: Naushir Patuck <naush@raspberrypi.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>