# SPDX-License-Identifier: LGPL-2.1-or-later
#
# Copyright (C) 2019, Google Inc.
#
%YAML 1.1
---
# Unless otherwise stated, all controls are bi-directional, i.e. they can be
# set through Request::controls() and returned out through Request::metadata().
controls:
  - AeEnable:
      type: bool
      description: |
        Enable or disable the AE.

        \sa ExposureTime AnalogueGain

  - AeLocked:
      type: bool
      description: |
        Report the lock status of a running AE algorithm.

        If the AE algorithm is locked the value shall be set to true, if it's
        converging it shall be set to false. If the AE algorithm is not
        running the control shall not be present in the metadata control list.

        \sa AeEnable

  # AeMeteringMode needs further attention:
  # - Auto-generate max enum value.
  # - Better handling of custom types.
  - AeMeteringMode:
      type: int32_t
      description: |
        Specify a metering mode for the AE algorithm to use. The metering
        modes determine which parts of the image are used to determine the
        scene brightness. Metering modes may be platform specific and not
        all metering modes may be supported.
      enum:
        - name: MeteringCentreWeighted
          value: 0
          description: Centre-weighted metering mode.
        - name: MeteringSpot
          value: 1
          description: Spot metering mode.
        - name: MeteringMatrix
          value: 2
          description: Matrix metering mode.
        - name: MeteringCustom
          value: 3
          description: Custom metering mode.

  # AeConstraintMode needs further attention:
  # - Auto-generate max enum value.
  # - Better handling of custom types.
  - AeConstraintMode:
      type: int32_t
      description: |
        Specify a constraint mode for the AE algorithm to use. These determine
        how the measured scene brightness is adjusted to reach the desired
        target exposure. Constraint modes may be platform specific, and not
        all constraint modes may be supported.
      enum:
        - name: ConstraintNormal
          value: 0
          description: Default constraint mode.
            This mode aims to balance the exposure of different parts of the
            image so as to reach a reasonable average level. However, highlights
            in the image may appear over-exposed and lowlights may appear
            under-exposed.
        - name: ConstraintHighlight
          value: 1
          description: Highlight constraint mode.
            This mode adjusts the exposure levels in order to try and avoid
            over-exposing the brightest parts (highlights) of an image.
            Other non-highlight parts of the image may appear under-exposed.
        - name: ConstraintShadows
          value: 2
          description: Shadows constraint mode.
            This mode adjusts the exposure levels in order to try and avoid
            under-exposing the dark parts (shadows) of an image. Other normally
            exposed parts of the image may appear over-exposed.
        - name: ConstraintCustom
          value: 3
          description: Custom constraint mode.

  # AeExposureMode needs further attention:
  # - Auto-generate max enum value.
  # - Better handling of custom types.
  - AeExposureMode:
      type: int32_t
      description: |
        Specify an exposure mode for the AE algorithm to use. These specify
        how the desired total exposure is divided between the shutter time
        and the sensor's analogue gain. The exposure modes are platform
        specific, and not all exposure modes may be supported.
      enum:
        - name: ExposureNormal
          value: 0
          description: Default exposure mode.
        - name: ExposureShort
          value: 1
          description: Exposure mode allowing only short exposure times.
        - name: ExposureLong
          value: 2
          description: Exposure mode allowing long exposure times.
        - name: ExposureCustom
          value: 3
          description: Custom exposure mode.

  - ExposureValue:
      type: float
      description: |
        Specify an Exposure Value (EV) parameter. The EV parameter will only be
        applied if the AE algorithm is currently enabled.

        By convention EV adjusts the exposure as log2. For example
        EV = [-2, -1, 0.5, 0, 0.5, 1, 2] results in an exposure adjustment
        of [1/4x, 1/2x, 1/sqrt(2)x, 1x, sqrt(2)x, 2x, 4x].

        \sa AeEnable

  - ExposureTime:
      type: int32_t
      description: |
        Exposure time (shutter speed) for the frame applied in the sensor
        device. This value is specified in micro-seconds.

        Setting this value means that it is now fixed and the AE algorithm may
        not change it. Setting it back to zero returns it to the control of the
        AE algorithm.

        \sa AnalogueGain AeEnable

        \todo Document the interactions between AeEnable and setting a fixed
        value for this control. Consider interactions with other AE features,
        such as aperture and aperture/shutter priority mode, and decide if
        control of which features should be automatically adjusted shouldn't
        better be handled through a separate AE mode control.

  - AnalogueGain:
      type: float
      description: |
        Analogue gain value applied in the sensor device.
        The value of the control specifies the gain multiplier applied to all
        colour channels. This value cannot be lower than 1.0.

        Setting this value means that it is now fixed and the AE algorithm may
        not change it. Setting it back to zero returns it to the control of the
        AE algorithm.

        \sa ExposureTime AeEnable

        \todo Document the interactions between AeEnable and setting a fixed
        value for this control. Consider interactions with other AE features,
        such as aperture and aperture/shutter priority mode, and decide if
        control of which features should be automatically adjusted shouldn't
        better be handled through a separate AE mode control.

  - Brightness:
      type: float
      description: |
        Specify a fixed brightness parameter. Positive values (up to 1.0)
        produce brighter images; negative values (up to -1.0) produce darker
        images and 0.0 leaves pixels unchanged.

  - Contrast:
      type: float
      description:  |
        Specify a fixed contrast parameter. Normal contrast is given by the
        value 1.0; larger values produce images with more contrast.

  - Lux:
      type: float
      description: |
        Report an estimate of the current illuminance level in lux. The Lux
        control can only be returned in metadata.

  - AwbEnable:
      type: bool
      description: |
        Enable or disable the AWB.

        \sa ColourGains

  # AwbMode needs further attention:
  # - Auto-generate max enum value.
  # - Better handling of custom types.
  - AwbMode:
      type: int32_t
      description: |
        Specify the range of illuminants to use for the AWB algorithm. The modes
        supported are platform specific, and not all modes may be supported.
      enum:
        - name: AwbAuto
          value: 0
          description: Search over the whole colour temperature range.
        - name: AwbIncandescent
          value: 1
          description: Incandescent AWB lamp mode.
        - name: AwbTungsten
          value: 2
          description: Tungsten AWB lamp mode.
        - name: AwbFluorescent
          value: 3
          description: Fluorescent AWB lamp mode.
        - name: AwbIndoor
          value: 4
          description: Indoor AWB lighting mode.
        - name: AwbDaylight
          value: 5
          description: Daylight AWB lighting mode.
        - name: AwbCloudy
          value: 6
          description: Cloudy AWB lighting mode.
        - name: AwbCustom
          value: 7
          description: Custom AWB mode.

  - AwbLocked:
      type: bool
      description: |
        Report the lock status of a running AWB algorithm.

        If the AWB algorithm is locked the value shall be set to true, if it's
        converging it shall be set to false. If the AWB algorithm is not
        running the control shall not be present in the metadata control list.

        \sa AwbEnable

  - ColourGains:
      type: float
      description: |
        Pair of gain values for the Red and Blue colour channels, in that
        order. ColourGains can only be applied in a Request when the AWB is
        disabled.

        \sa AwbEnable
      size: [2]

  - ColourTemperature:
      type: int32_t
      description: Report the current estimate of the colour temperature, in
        kelvin, for this frame. The ColourTemperature control can only be
        returned in metadata.

  - Saturation:
      type: float
      description:  |
        Specify a fixed saturation parameter. Normal saturation is given by
        the value 1.0; larger values produce more saturated colours; 0.0
        produces a greyscale image.

  - SensorBlackLevels:
      type: int32_t
      description: |
        Reports the sensor black levels used for processing a frame, in the
        order R, Gr, Gb, B. These values are returned as numbers out of a 16-bit
        pixel range (as if pixels ranged from 0 to 65535). The SensorBlackLevels
        control can only be returned in metadata.
      size: [4]

  - Sharpness:
      type: float
      description:  |
        A value of 0.0 means no sharpening. The minimum value means
        minimal sharpening, and shall be 0.0 unless the camera can't
        disable sharpening completely. The default value shall give a
        "reasonable" level of sharpening, suitable for most use cases.
        The maximum value may apply extremely high levels of sharpening,
        higher than anyone could reasonably want. Negative values are
        not allowed. Note also that sharpening is not applied to raw
        streams.

  - FocusFoM:
      type: int32_t
      description: |
        Reports a Figure of Merit (FoM) to indicate how in-focus the frame is.
        A larger FocusFoM value indicates a more in-focus frame. This control
        depends on the IPA to gather ISP statistics from the defined focus
        region, and combine them in a suitable way to generate a FocusFoM value.
        In this respect, it is not necessarily aimed at providing a way to
        implement a focus algorithm by the application, rather an indication of
        how in-focus a frame is.

  - ColourCorrectionMatrix:
      type: float
      description: |
        The 3x3 matrix that converts camera RGB to sRGB within the
        imaging pipeline. This should describe the matrix that is used
        after pixels have been white-balanced, but before any gamma
        transformation. The 3x3 matrix is stored in conventional reading
        order in an array of 9 floating point values.

      size: [3,3]

  - ScalerCrop:
      type: Rectangle
      description: |
        Sets the image portion that will be scaled to form the whole of
        the final output image. The (x,y) location of this rectangle is
        relative to the PixelArrayActiveAreas that is being used. The units
        remain native sensor pixels, even if the sensor is being used in
        a binning or skipping mode.

        This control is only present when the pipeline supports scaling. Its
        maximum valid value is given by the properties::ScalerCropMaximum
        property, and the two can be used to implement digital zoom.

  - DigitalGain:
      type: float
      description: |
        Digital gain value applied during the processing steps applied
        to the image as captured from the sensor.

        The global digital gain factor is applied to all the colour channels
        of the RAW image. Different pipeline models are free to
        specify how the global gain factor applies to each separate
        channel.

        If an imaging pipeline applies digital gain in distinct
        processing steps, this value indicates their total sum.
        Pipelines are free to decide how to adjust each processing
        step to respect the received gain factor and shall report
        their total value in the request metadata.

  - FrameDuration:
      type: int64_t
      description: |
        The instantaneous frame duration from start of frame exposure to start
        of next exposure, expressed in microseconds. This control is meant to
        be returned in metadata.

  - FrameDurationLimits:
      type: int64_t
      description: |
        The minimum and maximum (in that order) frame duration,
        expressed in microseconds.

        When provided by applications, the control specifies the sensor frame
        duration interval the pipeline has to use. This limits the largest
        exposure time the sensor can use. For example, if a maximum frame
        duration of 33ms is requested (corresponding to 30 frames per second),
        the sensor will not be able to raise the exposure time above 33ms.
        A fixed frame duration is achieved by setting the minimum and maximum
        values to be the same. Setting both values to 0 reverts to using the
        IPA provided defaults.

        The maximum frame duration provides the absolute limit to the shutter
        speed computed by the AE algorithm and it overrides any exposure mode
        setting specified with controls::AeExposureMode. Similarly, when a
        manual exposure time is set through controls::ExposureTime, it also
        gets clipped to the limits set by this control. When reported in
        metadata, the control expresses the minimum and maximum frame
        durations used after being clipped to the sensor provided frame
        duration limits.

        \sa AeExposureMode
        \sa ExposureTime

        \todo Define how to calculate the capture frame rate by
        defining controls to report additional delays introduced by
        the capture pipeline or post-processing stages (ie JPEG
        conversion, frame scaling).

        \todo Provide an explicit definition of default control values, for
        this and all other controls.

      size: [2]

  - SensorTemperature:
      type: float
      description: |
        Temperature measure from the camera sensor in Celsius. This is typically
        obtained by a thermal sensor present on-die or in the camera module. The
        range of reported temperatures is device dependent.

        The SensorTemperature control will only be returned in metadata if a
        themal sensor is present.

  - SensorTimestamp:
      type: int64_t
      description: |
        The time when the first row of the image sensor active array is exposed.

        The timestamp, expressed in nanoseconds, represents a monotonically
        increasing counter since the system boot time, as defined by the
        Linux-specific CLOCK_BOOTTIME clock id.

        The SensorTimestamp control can only be returned in metadata.

        \todo Define how the sensor timestamp has to be used in the reprocessing
        use case.

  - AfMode:
      type: int32_t
      description: |
        Control to set the mode of the AF (autofocus) algorithm.

        An implementation may choose not to implement all the modes.

      enum:
        - name: AfModeManual
          value: 0
          description: |
            The AF algorithm is in manual mode. In this mode it will never
            perform any action nor move the lens of its own accord, but an
            application can specify the desired lens position using the
            LensPosition control.

            In this mode the AfState will always report AfStateIdle.
        - name: AfModeAuto
          value: 1
          description: |
            The AF algorithm is in auto mode. This means that the algorithm
            will never move the lens or change state unless the AfTrigger
            control is used. The AfTrigger control can be used to initiate a
            focus scan, the results of which will be reported by AfState.

            If the autofocus algorithm is moved from AfModeAuto to another
            mode while a scan is in progress, the scan is cancelled
            immediately, without waiting for the scan to finish.

            When first entering this mode the AfState will report
            AfStateIdle. When a trigger control is sent, AfState will
            report AfStateScanning for a period before spontaneously
            changing to AfStateFocused or AfStateFailed, depending on
            the outcome of the scan. It will remain in this state until
            another scan is initiated by the AfTrigger control. If a scan is
            cancelled (without changing to another mode), AfState will return
            to AfStateIdle.
        - name: AfModeContinuous
          value: 2
          description: |
            The AF algorithm is in continuous mode. This means that the lens can
            re-start a scan spontaneously at any moment, without any user
            intervention. The AfState still reports whether the algorithm is
            currently scanning or not, though the application has no ability to
            initiate or cancel scans, nor to move the lens for itself.

            However, applications can pause the AF algorithm from continuously
            scanning by using the AfPause control. This allows video or still
            images to be captured whilst guaranteeing that the focus is fixed.

            When set to AfModeContinuous, the system will immediately initiate a
            scan so AfState will report AfStateScanning, and will settle on one
            of AfStateFocused or AfStateFailed, depending on the scan result.

  - AfRange:
      type: int32_t
      description: |
        Control to set the range of focus distances that is scanned. An
        implementation may choose not to implement all the options here.
      enum:
        - name: AfRangeNormal
          value: 0
          description: |
            A wide range of focus distances is scanned, all the way from
            infinity down to close distances, though depending on the
            implementation, possibly not including the very closest macro
            positions.
        - name: AfRangeMacro
          value: 1
          description: Only close distances are scanned.
        - name: AfRangeFull
          value: 2
          description: |
            The full range of focus distances is scanned just as with
            AfRangeNormal but this time including the very closest macro
            positions.

  - AfSpeed:
      type: int32_t
      description: |
        Control that determines whether the AF algorithm is to move the lens
        as quickly as possible or more steadily. For example, during video
        recording it may be desirable not to move the lens too abruptly, but
        when in a preview mode (waiting for a still capture) it may be
        helpful to move the lens as quickly as is reasonably possible.
      enum:
        - name: AfSpeedNormal
          value: 0
          description: Move the lens at its usual speed.
        - name: AfSpeedFast
          value: 1
          description: Move the lens more quickly.

  - AfMetering:
      type: int32_t
      description: |
        Instruct the AF algorithm how it should decide which parts of the image
        should be used to measure focus.
      enum:
        - name: AfMeteringAuto
          value: 0
          description: The AF algorithm should decide for itself where it will
            measure focus.
        - name: AfMeteringWindows
          value: 1
          description: The AF algorithm should use the rectangles defined by
            the AfWindows control to measure focus. If no windows are specified
            the behaviour is platform dependent.

  - AfWindows:
      type: Rectangle
      description: |
        Sets the focus windows used by the AF algorithm when AfMetering is set
        to AfMeteringWindows. The units used are pixels within the rectangle
        returned by the ScalerCropMaximum property.

        In order to be activated, a rectangle must be programmed with non-zero
        width and height. Internally, these rectangles are intersected with the
        ScalerCropMaximum rectangle. If the window becomes empty after this
        operation, then the window is ignored. If all the windows end up being
        ignored, then the behaviour is platform dependent.

        On platforms that support the ScalerCrop control (for implementing
        digital zoom, for example), no automatic recalculation or adjustment of
        AF windows is performed internally if the ScalerCrop is changed. If any
        window lies outside the output image after the scaler crop has been
        applied, it is up to the application to recalculate them.

        The details of how the windows are used are platform dependent. We note
        that when there is more than one AF window, a typical implementation
        might find the optimal focus position for each one and finally select
        the window where the focal distance for the objects shown in that part
        of the image are closest to the camera.

      size: [n]

  - AfTrigger:
      type: int32_t
      description: |
        This control starts an autofocus scan when AfMode is set to AfModeAuto,
        and can also be used to terminate a scan early.

        It is ignored if AfMode is set to AfModeManual or AfModeContinuous.

      enum:
        - name: AfTriggerStart
          value: 0
          description: Start an AF scan. Ignored if a scan is in progress.
        - name: AfTriggerCancel
          value: 1
          description: Cancel an AF scan. This does not cause the lens to move
            anywhere else. Ignored if no scan is in progress.

  - AfPause:
      type: int32_t
      description: |
        This control has no effect except when in continuous autofocus mode
        (AfModeContinuous). It can be used to pause any lens movements while
        (for example) images are captured. The algorithm remains inactive
        until it is instructed to resume.

      enum:
        - name: AfPauseImmediate
          value: 0
          description: |
            Pause the continuous autofocus algorithm immediately, whether or not
            any kind of scan is underway. AfPauseState will subsequently report
            AfPauseStatePaused. AfState may report any of AfStateScanning,
            AfStateFocused or AfStateFailed, depending on the algorithm's state
            when it received this control.
        - name: AfPauseDeferred
          value: 1
          description: |
            This is similar to AfPauseImmediate, and if the AfState is currently
            reporting AfStateFocused or AfStateFailed it will remain in that
            state and AfPauseState will report AfPauseStatePaused.

            However, if the algorithm is scanning (AfStateScanning),
            AfPauseState will report AfPauseStatePausing until the scan is
            finished, at which point AfState will report one of AfStateFocused
            or AfStateFailed, and AfPauseState will change to
            AfPauseStatePaused.

        - name: AfPauseResume
          value: 2
          description: |
            Resume continuous autofocus operation. The algorithm starts again
            from exactly where it left off, and AfPauseState will report
            AfPauseStateRunning.

  - LensPosition:
      type: float
      description: |
        Acts as a control to instruct the lens to move to a particular position
        and also reports back the position of the lens for each frame.

        The LensPosition control is ignored unless the AfMode is set to
        AfModeManual, though the value is reported back unconditionally in all
        modes.

        This value, which is generally a non-integer, is the reciprocal of the
        focal distance in metres, also known as dioptres. That is, to set a
        focal distance D, the lens position LP is given by

        \f$LP = \frac{1\mathrm{m}}{D}\f$

        For example:

        0 moves the lens to infinity.
        0.5 moves the lens to focus on objects 2m away.
        2 moves the lens to focus on objects 50cm away.
        And larger values will focus the lens closer.

        The default value of the control should indicate a good general position
        for the lens, often corresponding to the hyperfocal distance (the
        closest position for which objects at infinity are still acceptably
        sharp). The minimum will often be zero (meaning infinity), and the
        maximum value defines the closest focus position.

        \todo Define a property to report the Hyperfocal distance of calibrated
        lenses.

  - AfState:
      type: int32_t
      description: |
        Reports the current state of the AF algorithm in conjunction with the
        reported AfMode value and (in continuous AF mode) the AfPauseState
        value. The possible state changes are described below, though we note
        the following state transitions that occur when the AfMode is changed.

        If the AfMode is set to AfModeManual, then the AfState will always
        report AfStateIdle (even if the lens is subsequently moved). Changing to
        the AfModeManual state does not initiate any lens movement.

        If the AfMode is set to AfModeAuto then the AfState will report
        AfStateIdle. However, if AfModeAuto and AfTriggerStart are sent together
        then AfState will omit AfStateIdle and move straight to AfStateScanning
        (and start a scan).

        If the AfMode is set to AfModeContinuous then the AfState will initially
        report AfStateScanning.

      enum:
        - name: AfStateIdle
          value: 0
          description: |
            The AF algorithm is in manual mode (AfModeManual) or in auto mode
            (AfModeAuto) and a scan has not yet been triggered, or an
            in-progress scan was cancelled.
        - name: AfStateScanning
          value: 1
          description: |
            The AF algorithm is in auto mode (AfModeAuto), and a scan has been
            started using the AfTrigger control. The scan can be cancelled by
            sending AfTriggerCancel at which point the algorithm will either
            move back to AfStateIdle or, if the scan actually completes before
            the cancel request is processed, to one of AfStateFocused or
            AfStateFailed.

            Alternatively the AF algorithm could be in continuous mode
            (AfModeContinuous) at which point it may enter this state
            spontaneously whenever it determines that a rescan is needed.
        - name: AfStateFocused
          value: 2
          description: |
            The AF algorithm is in auto (AfModeAuto) or continuous
            (AfModeContinuous) mode and a scan has completed with the result
            that the algorithm believes the image is now in focus.
        - name: AfStateFailed
          value: 3
          description: |
            The AF algorithm is in auto (AfModeAuto) or continuous
            (AfModeContinuous) mode and a scan has completed with the result
            that the algorithm did not find a good focus position.

  - AfPauseState:
      type: int32_t
      description: |
        Only applicable in continuous (AfModeContinuous) mode, this reports
        whether the algorithm is currently running, paused or pausing (that is,
        will pause as soon as any in-progress scan completes).

        Any change to AfMode will cause AfPauseStateRunning to be reported.

      enum:
        - name: AfPauseStateRunning
          value: 0
          description: |
            Continuous AF is running and the algorithm may restart a scan
            spontaneously.
        - name: AfPauseStatePausing
          value: 1
          description: |
            Continuous AF has been sent an AfPauseDeferred control, and will
            pause as soon as any in-progress scan completes (and then report
            AfPauseStatePaused). No new scans will be start spontaneously until
            the AfPauseResume control is sent.
        - name: AfPauseStatePaused
          value: 2
          description: |
            Continuous AF is paused. No further state changes or lens movements
            will occur until the AfPauseResume control is sent.

  # ----------------------------------------------------------------------------
  # Draft controls section

  - AePrecaptureTrigger:
      type: int32_t
      draft: true
      description: |
        Control for AE metering trigger. Currently identical to
        ANDROID_CONTROL_AE_PRECAPTURE_TRIGGER.

        Whether the camera device will trigger a precapture metering sequence
        when it processes this request.
      enum:
        - name: AePrecaptureTriggerIdle
          value: 0
          description: The trigger is idle.
        - name: AePrecaptureTriggerStart
          value: 1
          description: The pre-capture AE metering is started by the camera.
        - name: AePrecaptureTriggerCancel
          value: 2
          description: |
            The camera will cancel any active or completed metering sequence.
            The AE algorithm is reset to its initial state.

  - NoiseReductionMode:
      type: int32_t
      draft: true
      description: |
       Control to select the noise reduction algorithm mode. Currently
       identical to ANDROID_NOISE_REDUCTION_MODE.

        Mode of operation for the noise reduction algorithm.
      enum:
        - name: NoiseReductionModeOff
          value: 0
          description: No noise reduction is applied
        - name: NoiseReductionModeFast
          value: 1
          description: |
            Noise reduction is applied without reducing the frame rate.
        - name: NoiseReductionModeHighQuality
          value: 2
          description: |
            High quality noise reduction at the expense of frame rate.
        - name: NoiseReductionModeMinimal
          value: 3
          description: |
            Minimal noise reduction is applied without reducing the frame rate.
        - name: NoiseReductionModeZSL
          value: 4
          description: |
            Noise reduction is applied at different levels to different streams.

  - ColorCorrectionAberrationMode:
      type: int32_t
      draft: true
      description: |
       Control to select the color correction aberration mode. Currently
       identical to ANDROID_COLOR_CORRECTION_ABERRATION_MODE.

        Mode of operation for the chromatic aberration correction algorithm.
      enum:
        - name: ColorCorrectionAberrationOff
          value: 0
          description: No aberration correction is applied.
        - name: ColorCorrectionAberrationFast
          value: 1
          description: Aberration correction will not slow down the frame rate.
        - name: ColorCorrectionAberrationHighQuality
          value: 2
          description: |
            High quality aberration correction which might reduce the frame
            rate.

  - AeState:
      type: int32_t
      draft: true
      description: |
       Control to report the current AE algorithm state. Currently identical to
       ANDROID_CONTROL_AE_STATE.

        Current state of the AE algorithm.
      enum:
        - name: AeStateInactive
          value: 0
          description: The AE algorithm is inactive.
        - name: AeStateSearching
          value: 1
          description: The AE algorithm has not converged yet.
        - name: AeStateConverged
          value: 2
          description: The AE algorithm has converged.
        - name: AeStateLocked
          value: 3
          description: The AE algorithm is locked.
        - name: AeStateFlashRequired
          value: 4
          description: The AE algorithm would need a flash for good results
        - name: AeStatePrecapture
          value: 5
          description: |
            The AE algorithm has started a pre-capture metering session.
            \sa AePrecaptureTrigger

  - AwbState:
      type: int32_t
      draft: true
      description: |
       Control to report the current AWB algorithm state. Currently identical
       to ANDROID_CONTROL_AWB_STATE.

        Current state of the AWB algorithm.
      enum:
        - name: AwbStateInactive
          value: 0
          description: The AWB algorithm is inactive.
        - name: AwbStateSearching
          value: 1
          description: The AWB algorithm has not converged yet.
        - name: AwbConverged
          value: 2
          description: The AWB algorithm has converged.
        - name: AwbLocked
          value: 3
          description: The AWB algorithm is locked.

  - SensorRollingShutterSkew:
      type: int64_t
      draft: true
      description: |
       Control to report the time between the start of exposure of the first
       row and the start of exposure of the last row. Currently identical to
       ANDROID_SENSOR_ROLLING_SHUTTER_SKEW

  - LensShadingMapMode:
      type: int32_t
      draft: true
      description: |
       Control to report if the lens shading map is available. Currently
       identical to ANDROID_STATISTICS_LENS_SHADING_MAP_MODE.
      enum:
        - name: LensShadingMapModeOff
          value: 0
          description: No lens shading map mode is available.
        - name: LensShadingMapModeOn
          value: 1
          description: The lens shading map mode is available.

  - SceneFlicker:
      type: int32_t
      draft: true
      description: |
       Control to report the detected scene light frequency. Currently
       identical to ANDROID_STATISTICS_SCENE_FLICKER.
      enum:
        - name: SceneFickerOff
          value: 0
          description: No flickering detected.
        - name: SceneFicker50Hz
          value: 1
          description: 50Hz flickering detected.
        - name: SceneFicker60Hz
          value: 2
          description: 60Hz flickering detected.

  - PipelineDepth:
      type: int32_t
      draft: true
      description: |
        Specifies the number of pipeline stages the frame went through from when
        it was exposed to when the final completed result was available to the
        framework. Always less than or equal to PipelineMaxDepth. Currently
        identical to ANDROID_REQUEST_PIPELINE_DEPTH.

        The typical value for this control is 3 as a frame is first exposed,
        captured and then processed in a single pass through the ISP. Any
        additional processing step performed after the ISP pass (in example face
        detection, additional format conversions etc) count as an additional
        pipeline stage.

  - MaxLatency:
      type: int32_t
      draft: true
      description: |
        The maximum number of frames that can occur after a request (different
        than the previous) has been submitted, and before the result's state
        becomes synchronized. A value of -1 indicates unknown latency, and 0
        indicates per-frame control. Currently identical to
        ANDROID_SYNC_MAX_LATENCY.

  - TestPatternMode:
      type: int32_t
      draft: true
      description: |
        Control to select the test pattern mode. Currently identical to
        ANDROID_SENSOR_TEST_PATTERN_MODE.
      enum:
        - name: TestPatternModeOff
          value: 0
          description: |
            No test pattern mode is used. The camera device returns frames from
            the image sensor.
        - name: TestPatternModeSolidColor
          value: 1
          description: |
            Each pixel in [R, G_even, G_odd, B] is replaced by its respective
            color channel provided in test pattern data.
            \todo Add control for test pattern data.
        - name: TestPatternModeColorBars
          value: 2
          description: |
            All pixel data is replaced with an 8-bar color pattern. The vertical
            bars (left-to-right) are as follows; white, yellow, cyan, green,
            magenta, red, blue and black. Each bar should take up 1/8 of the
            sensor pixel array width. When this is not possible, the bar size
            should be rounded down to the nearest integer and the pattern can
            repeat on the right side. Each bar's height must always take up the
            full sensor pixel array height.
        - name: TestPatternModeColorBarsFadeToGray
          value: 3
          description: |
            The test pattern is similar to TestPatternModeColorBars,
            except that each bar should start at its specified color at the top
            and fade to gray at the bottom. Furthermore each bar is further
            subdevided into a left and right half. The left half should have a
            smooth gradient, and the right half should have a quantized
            gradient. In particular, the right half's should consist of blocks
            of the same color for 1/16th active sensor pixel array width. The
            least significant bits in the quantized gradient should be copied
            from the most significant bits of the smooth gradient. The height of
            each bar should always be a multiple of 128. When this is not the
            case, the pattern should repeat at the bottom of the image.
        - name: TestPatternModePn9
          value: 4
          description: |
            All pixel data is replaced by a pseudo-random sequence generated
            from a PN9 512-bit sequence (typically implemented in hardware with
            a linear feedback shift register). The generator should be reset at
            the beginning of each frame, and thus each subsequent raw frame with
            this test pattern should be exactly the same as the last.
        - name: TestPatternModeCustom1
          value: 256
          description: |
            The first custom test pattern. All custom patterns that are
            available only on this camera device are at least this numeric
            value. All of the custom test patterns will be static (that is the
            raw image must not vary from frame to frame).

...